Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 383
9 - Passenger Occupant Detection System Control Module - J706-
❑ If the Passenger Occupant Detection System Control Module - J706- must be replaced, it is not necessary
to replace the passenger occupant detection system pressure sensor.
❑ Removing and installing. Refer to
⇒ “13.3 Passenger Occupant Detection System Control Module J706 , Removing and Installing”, page
.
10 - Connector
❑ Pay attention to the exact wire routing. Refer to
⇒ “13.2 Passenger Occupant Detection System Pressure Sensor, Removing and Installing”,
11 - Connector
❑ Voltage supply connector for Passenger Occupant Detection System Control Module - J706-
12 - Connector
❑ Coupling location of the passenger occupant detection system to the vehicle electrical system
13 - Front Seat Wiring Harness
13.2
Passenger Occupant Detection System
Pressure Sensor, Removing and Instal‐
ling
Note
♦
The passenger occupant detection system pressure sensor
and the front seat cushion can only be replaced as one unit.
♦
The Passenger Occupant Detection System Control Module -
J706- may not be replaced separately.
♦
Removing and installing the passenger occupant detection
system pressure sensor is described for the “Comfort” front
seat with manual seat adjustment.
♦
Removing and installing on the other versions of the front seat
is identical.
Removing
WARNING
♦ Observe the safety precautions for pyrotechnical compo‐
nents. Refer to
⇒ “1.2 Safety Precautions for Pyrotechnic Components”,
.
♦ Before handling pyrotechnic components (for example,
disconnecting the connector), the person handling it must
“discharge static electricity”. This can be done by touching
the door striker pin, for example.
– Remove the front seat. Refer to
⇒ “2.10 Front Seat, Removing and Installing”, page 335
– Secure the seat on the fixture for seat repair. Refer to
⇒ “1.2 Front Seat, Mounting on Fixture for Seat Repair”, page
.
– Remove the tunnel side seat trim. Refer to
– Remove the sill-side seat trim. Refer to
⇒ “2.14 Sill-Side Seat Trim, Removing and Installing”,
.
– Remove the seat trim bracket. Refer to
⇒ “2.15 Seat Trim Bracket, Removing and Installing”,
.
– Remove the storage compartment, if equipped. Refer to
⇒ “2.35 Storage Compartment, Removing and Installing”,
.
Note
The components pictured can vary in form and appearance from the present vehicle. However the assembly
and functionality are identical.
– Remove the front seat backrest -1-. Refer to
⇒ “2.16 Front Backrest, Removing and Installing”, page 349
– Disconnect the connector -4- for the passenger occupant de‐
tection system pressure sensor -2- from the Passenger Oc‐
cupant Detection System Control Module - J706- -3-.
– Loosen the passenger occupant detection system pressure
sensor wiring harness -5- from the seat frame.
– Remove the seat cushion with passenger occupant detection
system pressure sensor -2- and the cover from the seat frame.
Refer to
⇒ “1.4 Seat Pan Cover and Cushion, Removing and Installing”,
– Disconnect the cover from the seat cushion with passenger
occupant detection system pressure sensor -2-. Refer to
⇒ “1.6 Seat Pan Cover and Cushion, Separating”,
WARNING
The passenger occupant detection system pressure sensor
-2- is permanently glued to the seat cushion -1-. It is not pos‐
sible to remove and install separately. The passenger occu‐
pant detection system pressure sensor must be replaced with
the seat cushion.
On vehicles with seat heating, the passenger occupant detec‐
tion system pressure sensor and the seat heating element are
a shared component.
Note
♦
To prevent any removed components from being installed again by mistake, the components should be
separated from each other and disposed.
♦
The following work applies to these components.
♦
The components pictured can vary in form and appearance from the present vehicle. However the assembly
and functionality are identical.
– Remove the wiring harness -2- for the passenger occupant
detection system pressure sensor -3- from the channel and
guide it through the seat cushion -1-.
Note
The components pictured can vary in form and appearance from the present vehicle. However the assembly
and functionality are identical.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст