Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 1013
1 - O-Ring
❑ Coat with High Perform‐
ance Haldex Clutch Oil
and insert
❑ After removing replace
the Haldex Clutch
2 - All Wheel Drive Control
Module - J492-
❑ Removing and instal‐
ling, refer to
3 - Bolts
❑ 9.5 ± 0.5 Nm
❑ Quantity: 2
4 - Flange/Driveshaft Seal
Replacing, refer to
Axle Seal on Rear Final Drive,
5 - Flange/Driveshaft
❑ Removing and instal‐
ling, refer to
6 - Nut
❑ 210 Nm
❑ Replace after removing
❑ Secure using Locking
Compound - D 000 600- .
7 - Bolts
❑ 50 Nm
❑ Quantity: 4
8 - Haldex Clutch Housing
❑ Haldex clutch, removing and installing, refer to
⇒ “8.4 Haldex Clutch, Removing and Installing”, page 48
9 - O-Ring
❑ Quantity: 2
❑ Diameter 43.5 mm
❑ For Haldex Clutch Pump - V181-
❑ Coat with High Performance Haldex Clutch Oil and insert
❑ Always replace.
10 - Haldex Clutch Pump - V181-
❑ Removing and installing, refer to
⇒ “8.3 Haldex Clutch Pump V181 Removing and Installing”, page 46
11 - Bolt
❑ 9.5 ± 0.5 Nm
❑ Quantity: 2
Golf 2015 ➤
Rear Final Drive - Edition 09.2013
8. Haldex Clutch
45
12 - Rear Final Drive
❑ Removing and installing, refer to
⇒ “3.1 Final Drive, Removing and Installing”, page 20
8.3
Haldex Clutch Pump - V181- Removing
and Installing
⇒ “8.3.1 Haldex Clutch Pump V181 , Removing and Installing,
8.3.1
Haldex Clutch Pump - V181- , Removing
and Installing, Generation V
Special tools and workshop equipment required
♦ Used Oil Collection and Extraction Unit - SMN372500-
Removing
– Turn off the ignition.
– Place the Used Oil Collection and Extraction Unit -
SMN372500- under rear the final drive.
– Remove the drain plug -A- and completely drain the High Per‐
formance Haldex Clutch Oil .
– Install the drain plug -A- with the new sealing ring and tighten
to 30 Nm.
– Remove the connector -arrow- for the Haldex Clutch Pump -
V181- from the All Wheel Drive Control Module - J492- .
Golf 2015 ➤
Rear Final Drive - Edition 09.2013
46
Rep. Gr.39 - Final Drive, Differential
– Unclip and free up the wiring harness -3- for the Haldex Clutch
Pump - V181- from the housing.
Note
Ignore the bolt -arrow-.
– Place the Used Oil Collection and Extraction Unit -
SMN372500- under rear the final drive.
– Remove the bolt -1- from the Haldex Clutch Pump - V181- .
– Remove the Haldex Clutch Pump - V181- -2- from the Haldex
clutch housing.
Installing
Install in reverse order of removal. Note the following:
– If the removed Haldex Clutch Pump - V181- is being installed
again, replace the O-rings -1 and 2-.
– Lightly coat the O-rings -1 and 2- with High Performance Hal‐
dex Clutch Oil .
– Press the Haldex Clutch Pump - V181- -2- until stop in the
Haldex clutch housing. Make sure the wiring harness -3- is
routed correctly.
Note
Ignore the bolt -arrow-.
– Tighten the bolts -1-.
– Connect the connector -arrow- for the Haldex Clutch Pump -
V181- to the All Wheel Drive Control Module - J492- .
– Add High Performance Haldex Clutch Oil and check the oil
level in the Haldex clutch, refer to
⇒ “7 High-Performance Haldex Clutch Oil”, page 41
.
Tightening specifications
♦ Refer to Haldex Clutch Pump to Haldex clutch, refer to item
♦ Drain plug for High performance oil for Haldex clutch , refer to
⇒ “7 High-Performance Haldex Clutch Oil”, page 41
.
Golf 2015 ➤
Rear Final Drive - Edition 09.2013
8. Haldex Clutch
47
8.4
Haldex Clutch, Removing and Installing
⇒ “8.4.1 Haldex Clutch, Removing and Installing, Generation V”,
8.4.1
Haldex Clutch, Removing and Installing,
Generation V
Special tools and workshop equipment required
♦ Guide Pins - T10093-
♦ Counterhold - Kit - Multiple Use - T10172A- with Counterhold
- Kit - Adapter 5 - T10172/5-
♦ Used Oil Collection and Extraction Unit - SMN372500-
Removing
Caution
There is a danger of causing damage to the decoupling ele‐
ment.
♦ Do not bend the decoupling element more than 10°.
♦ Do not load the decoupling element.
♦ Do not damage the wire mesh on the decoupling element.
– Loosen the nuts for the clamping sleeve -arrows- and slide it
toward the rear.
– Tie the front exhaust pipe to the underbody.
– Remove the rear section of the exhaust system, refer to ⇒
Engine Mechanical, Fuel Injection and Ignition; Rep. Gr. 26 ;
Exhaust Pipes/Mufflers; Overview - Muffler .
– Loosen, but do not remove, the driveshaft center bearing bolts
-arrows-.
– Make sure there is a marking (a color dot) on the flexible disc/
the driveshaft flange on the rear final drive -arrows-.
– If the marking is not there, then mark the position of the flexible
disc/driveshaft to the driveshaft flange on the rear final drive.
Golf 2015 ➤
Rear Final Drive - Edition 09.2013
48
Rep. Gr.39 - Final Drive, Differential
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст