Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 574
– Remove the boot and, if possible, the noise insulation from the
center console. Refer to
⇒ “1.4 Gearshift Knob, Removing and Installing”, page 54
Secure the gearshift shaft as follows:
– Install the gearshift lever in neutral and, if necessary, press the
gearshift lever to the left and hold.
– Guide the Connecting Pin - T10027A- through the noise insu‐
lation -A-, hole -B- and into hole -C-.
– Position the safety mechanism on the cable retainer for the
shift cable and selector cable all the way to the right in direction
of -arrow-.
The spring will push the safety mechanism into the starting posi‐
tion.
– Push the angle -A- back in the starting position direction of
-arrow-.
• The bracket -A- must be pressed out of the selector housing
as far as the stop and it must face toward the rear.
– Remove the Locking Pin from the noise insulation -A- and the
holes -B and C-.
– Install the boot and if the insulation (if equipped). Refer to
⇒ “1.4 Gearshift Knob, Removing and Installing”, page 54
.
– Make sure the gearshift shaft moves easily.
– Install the air filter housing if it was removed earlier. Refer to
⇒ Engine Mechanical, Fuel Injection and Ignition; Rep. Gr.
24 ; Air Filter; Air Filter Housing, Removing and Installing .
1.7
Selector Mechanism, Checking
• The gearshift lever must rest in the 3rd/4th gear gate when the
transmission is in neutral.
– Operate the clutch.
– Move the gearshift lever (selector lever) several times through
all the gears. Make sure the reverse gear lock is working cor‐
rectly.
– It will be necessary to adjust the gearshift mechanism again if
a hook does not appear each time a gear is engaged. Refer
⇒ “1.6 Selector Mechanism, Adjusting”, page 63
1.8
Selector Shaft Seal, Replacing
Special tools and workshop equipment required
♦ Press Piece - Shift Rod/Alternator - VW423-
♦ Torque Wrench 1331 5-50Nm - VAG1331-
♦ Sealing Grease - G 052 128 A1-
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
– Remove transmission shift lever and relay lever. Refer to
⇒ “1.3 Overview - Selector Mechanism”, page 53
– Remove the seal with a screwdriver.
– Lightly oil new seal on outer circumference.
– Fill the space between the sealing and dust lip -arrow- halfway
with Sealing Grease - G 052 128 A1- .
– Drive in the seal using the Press Piece - Shift Rod/Alternator
- VW423- .
– Install the gearshift lever and relay lever. Refer to
⇒ “1.3 Overview - Selector Mechanism”, page 53
.
2
Transmission, Removing and Instal‐
ling
⇒ “2.1 Transmission, Removing”, page 67
⇒ “2.2 Transmission, Installing”, page 77
⇒ “2.3 Transmission Tightening Specifications”, page 86
2.1
Transmission, Removing
Special tools and workshop equipment required
♦ Engine Support Bridge - 10-222A-
♦ Engine Support Bridge - Gearbox Adapter - 10-222A/29-
♦ Engine Support Bridge - Engine Support 18 - 10-222A/18-
♦ Engine/Gearbox Support Shackle (2 pc.) - 10-222A/12-
♦ Transmission Support - Pins 29 - 3282/29-
♦ Transmission Support - 3282-
♦ Transmission Support - Mounting Plate 39 - 3282/39-
♦ Transmission Support Elements (determine when mounting
the Adjustment Plate on the Transmission Support )
♦ Engine and Gearbox Jack - VAS6931-
♦ Torque Wrench 1331 5-50Nm - VAG1331-
♦ Torque Wrench 1332 40-200Nm - VAG1332-
♦ Transmission Support Jig - 3336- to transport the transmis‐
sion.
♦ Grease for Clutch Disc Shaft Splines - G 000 100-
♦ Allocate the grease for gearshift mechanism. Refer to the
Parts Catalog.
♦ Engine Support Bridge - Special Hook (2 pc.) - 10-222A/20-
♦ Spindle from the Seal Installer - Driver Set - 3066- or M8 x 105
bolt
♦ Seal Installer - One-Piece Seal - T10148-
♦ Engine Support - Basic Set Square Pipe - T40091/1- (quantity
2)
♦ Engine Support - Basic Set Movable Joint - T40091/3- (quan‐
tity 2)
♦ Engine Support - Supplement Kit Spindle - T40093/3- (quan‐
tity 2) from the Engine Support - Supplement Kit - T40093A-
♦ Engine Support Brackets - T40093/3-6- (quantity 2)
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
Mandatory Replacement Parts
♦ Bolt - Transmission Support to Transmission
♦ Bolt - Transmission Support to Transmission Bracket
♦ Bolt - Pendulum Support to Transmission
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст