Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 572
1.5
Selector Mechanism, Removing and In‐
stalling
Special tools and workshop equipment required
♦ Torque Wrench 1331 5-50Nm - VAG1331-
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
Mandatory Replacement Parts
♦ Lock Washer - Cable Retainer
♦ Lock Washer - Gearshift Cable
Removing
– Disconnect the battery ground cable. Refer to ⇒ Electrical
Equipment; Rep. Gr. 27 ; Battery; Battery, Disconnecting and
Connecting .
– Remove the boot with the gearshift knob and, if necessary,
remove the noise insulation from the center console frame as
well. Refer to
⇒ “1.4 Gearshift Knob, Removing and Installing”, page 54
The Footwell Rear Channel is Located Above the Bracket for the
Center Console on Some Vehicles:
– Remove the center console. Refer to ⇒ Body Interior; Rep.
Gr. 68 ; Center Console; Center Console, Removing and In‐
stalling .
– Remove rear channel footwell. Refer to ⇒ Heating, Ventilation
and Air Conditioning; Rep. Gr. 87 ; Air Routing; Overview - Air
Routing and Air Distribution in Passenger Compartment .
– Remove the nuts from the center console mounting bracket.
Refer to ⇒ Body Interior; Rep. Gr. 68 ; Center Console; Center
Console, Removing and Installing .
– Remove the nuts from the gearshift housing. Refer to
⇒ Fig. ““Installed Position of Gearshift Housing
– Lower the gearshift housing.
• If it is not possible to lower the gearshift housing, then the nuts
on the gearshift housing are located under the bracket on the
center console.
• Remove the center console mounting bracket. Refer to ⇒
Body Interior; Rep. Gr. 68 ; Center Console; Center Console,
Removing and Installing .
If the Center Console Bracket Cannot be Removed Separately:
– Remove the center console. Refer to ⇒ Body Interior; Rep.
Gr. 68 ; Center Console; Center Console, Removing and In‐
stalling .
Installed Position of Gearshift Housing Nuts -arrows-.
– Remove the nuts -arrows-.
– Remove center console and center console mounting bracket.
Refer to ⇒ Body Interior; Rep. Gr. 68 ; Center Console; Over‐
view - Center Console .
– Remove rear channel footwell. Refer to ⇒ Heating, Ventilation
and Air Conditioning; Rep. Gr. 87 ; Air Routing; Overview - Air
Routing and Air Distribution in Passenger Compartment .
Installed Position of Noise Insulation and Gearshift Housing Nuts
-arrows-.
– Remove noise insulation and gearshift housing nuts
-arrows-.
– Remove noise insulation from the gearshift housing. Refer to
⇒ Body Interior; Rep. Gr. 68 ; Center Console; Overview -
Center Console .
– Remove the air filter housing if it is located over the gearshift
mechanism. Refer to ⇒ Engine Mechanical, Fuel Injection and
Glow Plug; Rep. Gr. 23 ; Air Filter; Overview - Air Filter Hous‐
ing or ⇒ Engine Mechanical, Fuel Injection and Ignition; Rep.
Gr. 24 ; Air Filter; Air Filter Housing, Removing and Installing .
– Remove the shift cable from the gearshift lever pins.
Disconnecting the Cable Retainer from the Selector Cable
– Pull the securing mechanism all the way forward in direction
of -arrow 1- and then unlock to the left in direction of
-arrow 2-.
– Push the relay lever forward (in direction of -arrow 3-).
Remove the Relay Lever and the Cable Retainer.
– Remove the clip -arrow 1- and then remove the relay lever
together with the cable retainer -arrow 2-.
– Remove the cable bracket from the transmission -arrows-.
Unclip the hose line -A- from the bracket -B- beforehand, if
necessary.
Caution
There is a danger of causing damage to the decoupling ele‐
ment on the exhaust pipe.
♦ Pay attention to ⇒ Rep. Gr. 26 ; Emissions Control; Over‐
view - Emissions Control .
– Remove the exhaust pipe under the gearshift mechanism. Re‐
fer to ⇒ Rep. Gr. 26 ; Exhaust Pipes/Mufflers; Overview -
Muffler .
– Remove the heat shield under the gearshift mechanism.
Removing the heat shield. Refer to ⇒ Body Exterior; Rep. Gr.
66 ; Molding/Trim/Extensions/Trim Panels; Floor Heat Shield,
Removing and Installing .
– Pivot shift housing downward and remove with cables.
With the Relay Lever Removed: Pry the Selector Cable Retainer
Off of the Relay Lever.
– Insert a screwdriver -A- between the bushing -B- and the relay
lever.
Installing
Install in reverse order of removal. Note the following:
Installing the Selector Cable Retainer on the Relay Lever
• The relay lever is removed.
• Lubricate cable retainer locating bore.
• Grease allocation. Refer to the Parts Catalog.
• The cable retainer may only be installed at the bushing in di‐
rection of -arrow-.
• The cable retainer must move freely on the relay lever.
• The cable retainer must be behind the tab.
• Make sure it engages securely.
– Align the shift housing so that is it parallel to the body.
• The distance on both sides to the body must be equal.
Install the gearshift housing.
Cable Tie Installation Locations
– Wrap the cable tie -arrow- in a crossover pattern around the
cables and attach it as illustrated.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст