Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 575
♦ Bolt - Pendulum Support to Subframe
♦ Bolts - Transmission Bracket to Transmission
♦ Bolts - Transmission Mount to Transmission Bracket
♦ Lock Washer - Cable Retainer
♦ Lock Washer - Gearshift Cable
♦ Nut - Coupling Rod to Stabilizer Bar
♦ Bolts - CV Boot to Inner CV Joint
♦ Seals - Transmission
– Disconnect the battery ground cable. Refer to ⇒ Electrical
Equipment; Rep. Gr. 27 ; Battery; Battery, Disconnecting and
Connecting .
– Remove the engine cover. Refer to ⇒ Rep. Gr. 10 ; Engine
Cover; Engine Cover, Removing and Installing .
– Remove the air filter housing. Refer to ⇒ Engine Mechanical,
Fuel Injection and Ignition; Rep. Gr. 24 ; Air Filter; Air Filter
Housing, Removing and Installing .
– Remove the battery and the battery tray -1- -arrows-. Refer to
⇒ Electrical Equipment; Rep. Gr. 27 ; Battery; Battery Tray,
Removing and Installing .
– Remove the cable retainer from the selector cable. Refer to
⇒ Fig. ““Disconnecting the Cable Retainer from the Selector
– Remove the clip -arrow 1- and then remove the relay lever and
the cable retainer.
– Remove the shift cable lock washer -arrow 2- from the selector
lever -A-.
– Remove the shift cable from the gearshift lever pins.
– Remove the nut -arrow 3- and then remove the transmission
shift lever -A-.
– Remove the cable mounting bracket from the transmission
-arrows-.
– Tie up the shift cable and the selector cable.
– If equipped, remove the bracket -B- from the transmission.
Remove the bracket from the hose/line assembly -A-.
– Remove the transmission support -A arrows-.
– Remove the clutch slave cylinder -B arrows- lay aside and se‐
cure with wire. Do not open the line system.
Caution
The clutch slave cylinder could be damaged.
♦ If the clutch slave cylinder is removed from the transmis‐
sion with pipe/hose line still connected, do not press the
clutch pedal.
– Remove the ground cable upward from the engine/transmis‐
sion connecting bolt or from the upper starter bolt.
– Disconnect the connector -arrow 1- from the Back-Up Lamp
Switch - F4- .
– Remove the connector -arrow 2- and wire -arrow 3- from the
starter.
– Remove the upper bolt from the starter.
– Remove the upper engine/transmission bolts.
– Unlock the retaining tab in direction of -arrow- and remove the
left engine cover mount -1-.
– Unclip the right mount -1- for the engine cover from the bracket
-2-.
– Attach the Engine Support Bridge - 10-222A- as follows:
The following are needed:
♦ Engine Support Bridge - Engine Support 18 - 10-222A/18-
♦ Engine Support - Bracket w/Spindle and hook - 10-222A/20-
♦ Engine/Gearbox Support Shackle (2 pc.) - 10-222A/12- (is
needed if the Spindle from the Engine Support Bridge cannot
be engaged in the engine lifting eye).
♦ Engine Support Bridge - Engine Support 29 - 10-222A/29-
(quantity 2)
♦ Engine Support - Basic Set Square Pipe - T40091/1- (quantity
2)
♦ Engine Support - Basic Set Movable Joint - T40091/3- (quan‐
tity 2)
♦ Engine Support - Supplement Kit Spindle - T40093/3- (quan‐
tity 2)
♦ Engine Support Brackets - T40093/3-6- (quantity 2)
– Insert the Engine Support Bridge - Engine Support 29 -
10-222A/29- between the fender bolting edge and the fender
bolting plate underneath it on both sides of the vehicle.
♦ Installed position:
“L” = -1- Adapter is Installed on the “right” Side of the Vehicle
( Adapter Locks in the Hole on the Fender).
“R” (Not Illustrated Here), Adapter is Installed on the “left” Side of
the Vehicle.
The arrow -2- on the Engine Support Bridge - Engine Support 29
- 10-222A/29- always points in the direction of travel.
– Slide the Engine Support Bridge - Engine Support 18 -
10-222A/18- and two Engine Support - Basic Set Movable
Joint - T40091/3- onto the Engine Support Bridge - 10-222A- .
– Tighten the Engine Support Bridge - 10-222A- on the Engine
Support Bridge - Engine Support 29 - 10-222A/29- .
-A- = Engine Support Brackets - T40093/3-6- (⇒ next illustration)
– Remove the filler tube for the windshield washer system wash‐
er fluid reservoir. Refer to ⇒ Electrical Equipment; Rep. Gr.
92 ; Windshield Washer System; Washer Fluid Reservoir, Re‐
moving and Installing .
– If present, remove wires from the front area of both longitudinal
members -arrow-. Do not disconnect line system.
– Place the Engine Support Brackets - T40093/3-6- on both lon‐
gitudinal members (the right longitudinal member is illustrated
here).
– If necessary, carefully unclip the A/C system pipe in the front
area. Do not disconnect the line system. Refer to ⇒ Heating,
Ventilation and Air Conditioning; Rep. Gr. 87 ; Refrigerant
Circuit; System Overview - Refrigerant Circuit .
• The Engine Support Brackets - T40093/3-6- locks respectively
with the pins -A- behind the tab on the longitudinal member
-arrow-.
– Install the Engine Support - Supplement Kit Spindle -
T40093/3- .
– Connect the Engine Support - Supplement Kit Spindle -
T40093/3- over the Engine Support - Basic Set Square Pipe -
T40091/1- with the Engine Support Bridge - 10-222A- and
tension it (⇒ previous illustration).
Note
♦
The Engine Support - Basic Set - Square Pipe - T40091/1-
must not touch the windshield.
♦
The Engine Support Bridge - Engine Support 18 - 10-222A/18-
must not lie on the windshield wiper arm.
– Engage the Spindles with the Engine Support Bridge - Special
Hook (2 pc.) - 10-222A/20- and if necessary with the Engine/
Gearbox Support Shackle (2 pc.) - 10-222A/12- in the engine
lifting eyes.
– Pretension the engine/transmission assembly and Engine
Support Bridge via the Spindles .
– Raise the vehicle and remove the left front wheel.
– Remove the noise insulation. Refer to ⇒ Body Exterior; Rep.
Gr. 66 ; Noise Insulation; Overview - Noise Insulation .
– Remove the lower section of the left front wheel housing liner.
Refer to ⇒ Body Exterior; Rep. Gr. 66 ; Wheel Housing Liner;
Front Wheel Housing Liner, Removing and Installing .
– Remove the nut -arrow- and then remove the wire mount.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст