Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 351
– Fold up the roof grab handle -1-. As a result, the caps -2- en‐
gage audibly into the locking position.
– Fold the roof grab handle down and check if both caps are
completely engaged in the roof grab handle. This is the case
if the caps and the respective roof grab handle base form a
flat surface.
2.11
Roof Grab Handle Bracket, Removing
and Installing
Note
The removal and installation for the left front roof grab handle
bracket is described. The removal and installation of the other roof
grab handle brackets is identical.
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Removing
– Remove the headliner. Refer to
⇒ “7.3 Headliner, Removing and Installing”, page 299
.
– If equipped, unclip the wiring guide -1- from the roof grab han‐
dle bracket -3-.
– Remove the screws -2- and remove the roof grab handle
bracket -3-.
Installing
Note
Check all the fasteners for damage and replace if necessary.
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
3
Center Console
⇒ “3.1 Overview - Center Console”, page 53
⇒ “3.2 Front Ashtray, Removing and Installing”, page 55
⇒ “3.3 Center Console Rear Trim, Removing and Installing”, page
55
⇒ “3.4 Front Footwell Center Console Trim Panel, Removing and
Installing”, page 55
⇒ “3.5 Display and Control Unit Trim, Removing and Installing”,
page 56
⇒ “3.6 Front Center Console Storage Compartment, Removing
and Installing”, page 57
⇒ “3.7 Center Console Cover, Removing and Installing”,
page 57
⇒ “3.8 Center Console, Removing and Installing”, page 59
⇒ “3.9 Center Console Bracket, Removing and Installing”,
3.1
Overview - Center Console
1 - Display and Control Unit
Trim
❑ Removing and instal‐
ling. Refer to
.
2 - Front Center Console Stor‐
age Compartment
❑ Removing and instal‐
ling. Refer to
.
3 - Service Door Storage Com‐
partment Mat
❑ Placed in the center
console
4 - Footwell Center Console
Trim Panel
❑ Left and right
❑ Removing and instal‐
ling. Refer to
5 - Screw
❑ 1.5 Nm
❑ Quantity: 2
6 - Service Door
❑ Clipped in the center
console
7 - Screw
❑ 1.5 Nm
❑ Quantity: 2
8 - Shift Mechanism Cover
❑ Removing and installing. Refer to
⇒ “3.7 Center Console Cover, Removing and Installing”, page 57
9 - Screw
❑ 1.5 Nm
❑ Quantity: 2
10 - Cap
❑ Clipped in the center console
11 - Clip
❑ Clipped in the center console
12 - Center Console
❑ Removing and installing. Refer to
⇒ “3.8 Center Console, Removing and Installing”, page 59
.
13 - Screw
❑ 6 Nm
❑ Quantity: 2
14 - Cap
❑ Left and right
❑ Push in the center console
15 - Center Console Rear Trim
❑ Removing and installing. Refer to
⇒ “3.3 Center Console Rear Trim, Removing and Installing”, page 55
.
16 - Screw
❑ 6 Nm
❑ Quantity: 2
17 - Bracket Behind Shifting Mechanism
❑ Clipped on the gearshift mechanism noise insulation
18 - Shifting Mechanism Noise Insulation
19 - Bracket in Front of Shifting Mechanism
❑ For the center console
❑ Removing and installing. Refer to
⇒ “3.9 Center Console Bracket, Removing and Installing”, page 61
.
20 - Screw
❑ 1.5 Nm
❑ Quantity: 2
21 - Screw
❑ 6 Nm
22 - Bracket
❑ For the footwell center console trim panel
❑ Clipped with the heater and A/C unit
3.2
Front Ashtray, Removing and Installing
Removing
– Remove the front ashtray -1- upward from the center console
-2-.
Installing
Install in reverse order of removal.
3.3
Center Console Rear Trim, Removing
and Installing
Special tools and workshop equipment required
♦ Backrest Panel Tool - 3370-
Removing
– Move the front seats all the way forward.
– Pull the rear trim -1- at the lower end off of the center console
-2- toward the rear.
– Pull the rear trim -1- upward off of the center console -2-
-arrow- and remove it.
Installing
Note
Check all the fasteners for damage and replace if necessary.
Install in reverse order of removal.
3.4
Front Footwell Center Console Trim
Panel, Removing and Installing
Note
Removal and installation are described for the footwell center
console trim panel on the driver side. The removal and installation
for the front passenger side is identical.
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Removing
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст