Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 352
– Remove the bolt -3-.
– Pull the footwell center console trim panel -1- downward off of
the mounts for the center console -2- and remove.
Installing
Note
Check all the fasteners for damage and replace if necessary.
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
⇒ “3.4 Front Footwell Center Console Trim Panel, Removing
3.5
Display and Control Unit Trim, Remov‐
ing and Installing
Special tools and workshop equipment required
♦ Trim Removal Wedge - 3409-
Removing
– Loosen but do not remove the center instrument panel panel
trim in the lower area using -3409- .
– Unclip the display and control unit trim -1- from the display and
control unit -2- starting at the bottom and remove.
Installing
Note
Check all the fasteners for damage and replace if necessary.
Install in reverse order of removal.
3.6
Front Center Console Storage Compart‐
ment, Removing and Installing
Removing
– Remove the display and control head trim. Refer to
⇒ “3.5 Display and Control Unit Trim, Removing and Instal‐
.
– Unclip the front storage compartment -1- from the center con‐
sole -2- -arrows A-.
– Remove the front storage compartment -1- from the center
console -2- toward the rear -arrow B-.
– If equipped, disconnect the connectors from the front storage
compartment.
Installing
Note
♦
Check all the fasteners for damage and replace if necessary.
♦
Make sure the tab on the front storage compartment is seated
correctly in the center console hole.
Install in reverse order of removal.
Note
When installing, position the storage compartment at a slight an‐
gle in order to insert it into the rear guide. Then press the storage
compartment downward and lock in place.
3.7
Center Console Cover, Removing and
Installing
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Removing
– For vehicles with a Direct Shift Gearbox (DSG) transmission,
move the selector lever into “D/S”.
– Switch off the ignition.
– Carefully unclip the selector lever/shift lever boot from the
center console and fold it upward.
– Remove the front storage compartment. Refer to
⇒ “3.6 Front Center Console Storage Compartment, Remov‐
.
– Remove the bolts -2-.
– Remove the gearshift mechanism cover -1- from the center
console in the direction of the -arrow- until the connectors are
accessible.
– Release and disconnect any existing connectors.
– Carefully remove the gearshift mechanism cover -1- over the
selector lever/gearshift lever.
Installing
Note
Check all the fasteners for damage and replace if necessary.
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
⇒ “3.1 Overview - Center Console”, page 53
3.8
Center Console, Removing and Instal‐
ling
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Removing
– Remove the center console rear trim. Refer to
⇒ “3.3 Center Console Rear Trim, Removing and Installing”,
– Remove the gearshift mechanism cover. Refer to
⇒ “3.7 Center Console Cover, Removing and Installing”, page
.
– Remove the parking brake lever trim. Refer to
⇒ “1.20 Parking Brake Lever Trim, Removing and Installing”,
– Remove the left and right footwell center console trim panels.
Refer to
⇒ “3.4 Front Footwell Center Console Trim Panel, Removing
– Remove the display and control unit. Refer to ⇒ Heating,
Ventilation and Air Conditioning; Rep. Gr. 87 ; Display and
Control Head; Display and Control Head, Removing and In‐
stalling .
– Remove the mounting bracket in front of the gearshift mech‐
anism. Refer to
⇒ “3.9 Center Console Bracket, Removing and Installing”,
– Remove the bolts -1- for the center console -2-.
– If equipped, release and disconnect the connector -3- for the
12 V socket.
– Move the front seats as far forward as possible using the for‐
ward/back adjuster.
– Remove the left and right cap -1- from the center console
-3-.
– Remove the bolt -2- for the center console -3- on the left and
right sides.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст