Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 470
3.3
Transmission Tightening Specifications
Transmission to Engine
Item
Bolt
Nm
1
M12 x 55
80
• With Insert Tool -
18mm T10179:
“65 Nm”
2
M10 x 45
♦ Starter to trans‐
mission
40
3
M12 x 55
♦ Is accessible on‐
ly through the
opening in the
removed starter
80
4
M10 x 45
or M10 x 40
♦ Starter to trans‐
mission
40
5
M12 x 65
or M12 x 70
80
6
M10 x 50
40
7
M10 x 50
40
8
M10 x 50
40
9
M12 x 65
or M12 x 70
or M12 x 80
80
10
M12 x 55
80
• With Insert Tool -
18mm T10179:
“65 Nm”
A
Alignment sleeve for centering
Component
Tightening Specification
Cable bracket on the transmis‐
sion cover
10 Nm
Transmission Coolant Valve -
N488- bolts
9 Nm
4
Subframe Mount
⇒ “4.1 Overview - Subframe Mount”, page 97
.
4.1
Overview - Subframe Mount
1 - Bolt
❑ For the tightening spec‐
ification. Refer to ⇒ En‐
gine Mechanical, Fuel
Injection and Ignition;
Rep. Gr. 10 ; Subframe
Mount; Overview - Sub‐
frame Mount .
2 - Engine Support
❑ Refer to ⇒ Engine Me‐
chanical, Fuel Injection
and Ignition; Rep. Gr.
10 ; Subframe Mount;
Overview - Subframe
Mount .
3 - Engine Mount
❑ Refer to ⇒ Engine Me‐
chanical, Fuel Injection
and Ignition; Rep. Gr.
10 ; Subframe Mount;
Overview - Subframe
Mount .
4 - Bolt
❑ For the tightening spec‐
ification. Refer to ⇒ En‐
gine Mechanical, Fuel
Injection and Ignition;
Rep. Gr. 10 ; Subframe
Mount; Overview - Sub‐
frame Mount .
5 - Bolt
❑ For the tightening spec‐
ification. Refer to ⇒ En‐
gine Mechanical, Fuel
Injection and Ignition;
Rep. Gr. 10 ; Subframe
Mount; Overview - Subframe Mount .
6 - Bolt
❑ For the tightening specification. Refer to ⇒ Engine Mechanical, Fuel Injection and Ignition; Rep. Gr. 10 ;
Subframe Mount; Overview - Subframe Mount .
7 - Bolt
❑ For the tightening specification. Refer to ⇒ Engine Mechanical, Fuel Injection and Ignition; Rep. Gr. 10 ;
Subframe Mount; Overview - Subframe Mount .
8 - Pendulum Support
9 - Bolt
❑ For pendulum support to subframe
❑ For the tightening specification. Refer to ⇒ Engine Mechanical, Fuel Injection and Ignition; Rep. Gr. 10 ;
Subframe Mount; Overview - Subframe Mount .
10 - Bolt
❑ For pendulum support to transmission
❑ Transmission with threaded insert. Refer to
❑ For the tightening specification. Refer to ⇒ Engine Mechanical, Fuel Injection and Ignition; Rep. Gr. 10 ;
Subframe Mount; Overview - Subframe Mount .
11 - Bolt
❑ For pendulum support to transmission
❑ Transmission with threaded insert. Refer to
❑ For the tightening specification. Refer to ⇒ Engine Mechanical, Fuel Injection and Ignition; Rep. Gr. 10 ;
Subframe Mount; Overview - Subframe Mount .
12 - Bolt
❑ 60 Nm + 90°
❑ Replace after removing
❑ For transmission mount to transmission bracket
❑ Tightening sequence. Refer to
13 - Bolt
❑ 60 Nm + 90°
❑ Replace after removing
❑ Quantity: 2
❑ For transmission mount to transmission bracket
❑ Tightening sequence. Refer to
14 - Transmission Mount
❑ Check the adjustment. Refer to ⇒ Engine Mechanical, Fuel Injection and Ignition; Rep. Gr. 10 ; Subframe
Mount; Subframe Mount, Checking Adjustment
❑ Adjusting. Refer to ⇒ Engine Mechanical, Fuel Injection and Ignition; Rep. Gr. 10 ; Subframe Mount;
Subframe Mount, Adjusting
15 - Bolt
❑ Transmission mount to chassis
❑ For the tightening specification. Refer to ⇒ Engine Mechanical, Fuel Injection and Ignition; Rep. Gr. 10 ;
Subframe Mount; Subframe Mount, Adjusting .
16 - Bolt
❑ 40 Nm + 90°
❑ Replace after removing
❑ For transmission bracket to transmission
❑ Tightening sequence. Refer to
17 - Transmission Bracket
❑ Illustration does not correspond to version in vehicle
18 - Bolt
❑ 40 Nm 90°
❑ Replace after removing
❑ For transmission bracket to transmission
❑ Tightening sequence. Refer to
Transmission with Threaded Insert (for Example “Heli Coil”) for
Attaching the Pendulum Support
Note
♦
There are threaded inserts (for example “Heli Coil”) in the pen‐
dulum support fastening holes.
♦
Identified by: collar on the first thread -arrow-.
♦
Make sure to use the appropriate bolts and observe the tight‐
ening specification. Refer to ⇒ Engine Mechanical, Fuel In‐
jection and Ignition; Rep. Gr. 10 ; Subframe Mount; Overview
- Subframe Mount ..
Install the Left Subframe Mount as Follows:
– Replace all the bolts -1 and 2-.
– Install the new bolt first hand-tight.
– Install the bolts -1- in the transmission bracket -A-.
– Pry the transmission bracket -A- into the seat using a screw‐
driver while tightening the bolts -2-.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст