Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 943
1 - Ignition Key
2 - Lock Cylinder
❑ Removing and instal‐
ling. Refer to
.
3 - Anti-Theft Immobilizer
Reader Coil - D2-
❑ Removing and instal‐
ling. Refer to
.
4 - Mount
❑ With Turn Signal Switch
- E2- / Windshield Wiper
Intermittent Mode
Switch - E22-
❑ With cruise control: with
Cruise Control Switch -
E45-
❑ Removing and instal‐
ling. Refer to
.
5 - Steering Column Electron‐
ics Control Module - J527-
❑ With Airbag Spiral
Spring/Return Spring
with Slip Ring - F138-
❑ Removing and installing. Refer to
⇒ “8.6 Steering Column Electronics Control Module J527 , Removing and Installing”, page 187
.
Caution
Risk of damaging the re‐
turn ring.
♦
The return spring with
slip ring must not be
turned after removing.
6 - Screw
❑ 1 Nm
❑ Quantity: 3
7 - Ignition/Starter Switch - D-
❑ Removing and installing. Refer to
⇒ “8.4 Ignition/Starter Switch, Removing and Installing”, page 181
.
8 - Steering Lock Housing
❑ Removing and installing. Refer to
⇒ “8.11 Steering Lock Housing, Removing and Installing”, page 195
.
9 - Screw
❑ 1 Nm
10 - Ignition Switch Key Lock Solenoid - N376-
❑ For DSG transmission
❑ Removing and installing. Refer to
⇒ “8.3 Ignition Switch Key Lock Solenoid N376 , Removing and Installing”, page 180
11 - Steering Column
12 - Bolt
❑ Quantity: 2
❑ For steering lock housing (shear bolt)
8.1.2
Overview - Steering Column Switch Module and Electronic Ignition Switch
1 - Start System Button - E378-
❑ Removing and instal‐
ling. Refer to
2 - Steering Column Electron‐
ics Control Module - J527-
❑ With Airbag Spiral
Spring/Return Spring
with Slip Ring - F138-
❑ Removing and instal‐
ling. Refer to
.
Caution
Risk of damaging the re‐
turn ring.
♦
The return spring with
slip ring must not be
turned after removing.
3 - Screw
❑ 1 Nm
❑ Quantity: 3
4 - Mount
❑ With Turn Signal Switch
- E2- , Windshield Wiper
Intermittent Mode
Switch - E22-
❑ With cruise control: with Cruise Control Switch - E45-
❑ Removing and installing. Refer to
⇒ “8.7 Turn Signal Switch E2 , Removing and Installing”, page 192
5 - Electronic Steering Column Lock Control Module - J764-
❑ Removing and installing. Refer to ⇒ Suspension, Wheels, Steering; Rep. Gr. 48 ; Steering Column;
Electronic Steering Column Lock Control Module - J764- , Removing and Installing
6 - Screw
❑ 1 Nm
7 - Steering Column
8 - Bolt
❑ Quantity: 2
❑ For Electronic Steering Column Lock Control Module - J764- (shear bolt)
9 - Anti-Theft Immobilizer Reader Coil - D2-
❑ Removing and installing. Refer to
⇒ “8.10.2 Anti-Theft Immobilizer Reader Coil D2 , Removing and Installing, Vehicles with Keyless Ac‐
10 - Ignition Key
8.2
Lock Cylinder, Removing and Installing
Special tools and workshop equipment required
♦ Locking Pin (3 pc.) - T40011- or
♦ Suitable welding wire
For removing the lock cylinder, it may be necessary to fold in the
ignition key.
Removing
Right lock position is shown without ignition lock to provide a bet‐
ter illustration.
– Remove the lower steering column trim panel. Refer to ⇒ Body
Interior; Rep. Gr. 68 ; Storage Compartments and Covers;
Lower Steering Column Trim Panel, Removing and Installing .
– Turn the ignition key in the ignition “on” position. While doing
so the cut out in the trim -arrow- aligns with the hole in the
ignition lock.
– Fold the ignition key as far as it possible.
– Push in -T40011- or a suitable welding wire until stop in the
hole -2-.
– Remove the lock cylinder -1- from the steering lock housing.
WARNING
Risk of steering lock seizing.
♦ Steering lock must not be operated without a lock cylinder.
A blocked steering lock must be replaced.
The Anti-Theft Immobilizer Reader Coil - D2- is integrated in the
lock cylinder and cannot be replaced separately. If the Anti-Theft
Immobilizer Reader Coil - D2- is faulty, the complete lock cylinder
must be replaced.
With the vehicle-specific lock number, a new lock cylinder is or‐
dered through the distributor or importer using the VIN.
– Release and disconnect the connector from the Anti-Theft Im‐
mobilizer Reader Coil - D2- .
Installing
Install in the reverse order of removal while paying attention to
the following:
– Insert the ignition key into the lock cylinder and turn it to the
ignition “on” position.
– Push the -T40011- or a suitable welding wire back in the front
side hole until stop.
– Connect the connector to the Anti-Theft Immobilizer Reader
Coil - D2- .
– Push in the lock cylinder -1- with the Anti-Theft Immobilizer
Reader Coil - D2- in the steering lock housing -3-.
– Remove the -T40011- from the hole -2-.
– Push the lock cylinder in securely until the locking mechanism
engages audibly.
8.3
Ignition Switch Key Lock Solenoid -
N376- , Removing and Installing
Removing
– Turn off the ignition and all electrical equipment.
– Remove the ignition key, if equipped.
– Remove the lower steering column trim panel. Refer to ⇒ Body
Interior; Rep. Gr. 68 ; Storage Compartments and Covers;
Lower Steering Column Trim Panel, Removing and Installing .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст