Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 972
– Remove the nuts -1, 2, 4, 5 and 6-.
– Remove the bolt -3-.
– Free up the wire -arrow-.
– Cut the lower cable ties on the wiring harness.
– Release the retainers -1, 2 and 4- in direction of -arrow-, re‐
move the Fuse Panel B - SB- -3- and set it aside.
Installing
Install in the reverse order of removal while paying attention to
the following:
– Attach and tighten the wires according to the markings on
Fuse Panel A - SA- .
Tightening Specifications
♦ Refer to
⇒ “1.1.1 Relay Carriers, Fuse Panels and E-Boxes”,
1.3.2
Fuse Panel A - SA- , Removing and In‐
stalling
Removing
– Remove the Fuse Panel B - SB- . Refer to
⇒ “1.3 E-Box Relay and Fuse Panels, Removing and Instal‐
– Remove the mounting bracket -4- upward from the Fuse Panel
B - SB- .
– Release the mounting tab -1- in direction of -arrow- and fuse
panel A -2- downward from the fuse panel B -3-.
Installing
Install in reverse order of removal.
1.4
Relay and Fuse Carrier Behind Instru‐
ment Panel on Driver Side, Removing
and Installing
Removing
– Disconnect the Battery - A- . Refer to
⇒ “1.3 Battery, Disconnecting and Connecting”, page 9
.
– Remove the instrument panel. Refer to ⇒ Body Interior; Rep.
Gr. 70 ; Instrument Panel; Instrument Panel, Removing and
Installing .
– Release the mounting tab -2 and 4- -A arrows-.
– Remove fuse panel C -3- to the rear from the bracket -1-
-arrow B-.
– Remove the wires.
The exact assignment can be found the applicable wiring dia‐
gram. Refer to ⇒ Wiring diagrams, Troubleshooting & Component
locations.
Note
Take photos of the alignment.
Installing
Install in reverse order of removal.
2
Control Modules
⇒ “2.1 Component Location Overview - Control Modules”,
page 295
⇒ “2.2 Overview - Control Modules”, page 298
⇒ “2.3 Overview - Data Bus On Board Diagnostic Interface”, page
299
⇒ “2.4 Vehicle Electrical System Control Module J519 , Removing
and Installing”, page 299
⇒ “2.5 Data Bus On Board Diagnostic Interface J533 , Removing
and Installing”, page 300
⇒ “2.6 Vehicle Electrical System Control Module J519 Bracket,
Removing and Installing”, page 301
⇒ “2.7 Vehicle Electrical System Control Module J519 Bracket,
Replacing”, page 302
⇒ “2.8 Parking Aid Control Module J446 / Parallel Parking As‐
sistance Control Module J791 Bracket, Removing and Installing”,
2.1
Component Location Overview - Control
Modules
⇒ “2.1.1 Component Location Overview - Front Control Modules”,
page 295
⇒ “2.1.2 Component Location Overview - Rear Control Modules”,
2.1.1
Component Location Overview - Front Control Modules
Note
The component locations for the Sedan are shown. The component locations for the Wagon are identical.
1 - Data Bus On Board Diag‐
nostic Interface - J533-
❑ Overview. Refer to
2 - Bracket
❑ Overview. Refer to
3 - Vehicle Electrical System
Control Module - J519-
❑ Overview. Refer to
4 - Bracket
❑ Overview. Refer to
.
5 - Parking Aid Control Module
- J446- / Parallel Parking As‐
sistance Control Module -
J791-
❑ Overview. Refer to
.
6 - Access/Start System Inter‐
face - J965-
❑ Component location
overview. Refer to
cation Overview - Access/Start Authorization System”, page 166
.
7 - Headlamp Range Control Module - J431- / Cornering Lamp and Headlamp Range Control Module - J745-
❑ Overview. Refer to
⇒ “11.1 Overview - Automatic Headlamp Range Control”, page 209
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст