Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 435
– Remove the pass-through cover frame.
– Push the backrest cushion with backrest cover slightly aside,
and unclip the pass-through door stop strip -1- from the rear
seat backrest in direction of -arrows-.
– Remove the pass-through door stop strip.
Installing
Install in reverse order of removal.
3.12
Pass-Through Door, Removing and In‐
stalling
Special tools and workshop equipment required
♦ Torque Wrench 1410 - VAG1410-
Removing
– Fold down the center armrest and open the pass-through door.
– Remove the bolts -2-.
– Remove the center armrest with the cover -1- for the pass
through.
– Remove the center armrest. Refer to
– Remove the lower center cushion. Refer to
⇒ “2.5 Center Cushion, Removing and Installing, Backrest with
Installing
– Install the pass-through door -1- and the center armrest and
tighten the bolts hand tight.
– Close the pass-through door and align.
– Tighten the bolts -2- on the rear seat backrest.
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
⇒ “3.4 Overview - Center Armrest”, page 380
3.13
Center Armrest, Removing and Instal‐
ling
Special tools and workshop equipment required
♦ Torque Wrench 1410 - VAG1410-
Removing
– Open the pass through door -2- with the center armrest ap‐
proximately
1
/3.
– Remove the bolts -arrows-.
– Remove the renter armrest -1- from the pass-through door.
Installing
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
3.14
Headrest, Removing and Installing
Removing
– Press the height adjustment release button -3- on the headrest
guide -4- in direction of the -arrow-.
– At the same time, remove the headrest -1- all the way from the
rear seat backrest -2-.
– Using a small flat-head screwdriver, press the locking spring
as far as the stop through the opening -arrow- in the headrest
guide -1-.
Note
The position of the opening in the headrest guide -arrow- can ei‐
ther be in direction of travel »on the right« or »on the left side«.
– At the same time, remove the headrest -2- from the rear seat
backrest -3-.
Installing
Install in reverse order of removal.
3.15
Headrest Guide, Removing and Instal‐
ling
Note
Two commercially available screwdrivers are required for remov‐
al. Blade height: 0.4 mm, blade width: 8 mm.
Removing
– Remove the rear headrest. Refer to
⇒ “3.14 Headrest, Removing and Installing”, page 390
– Press the backrest cover with backrest cushion -1- slightly
downward at the outer sides.
– Insert a screwdriver on each side of the headrest tube -3- up
to the height of the tabs in direction of -arrows- in the backrest.
Note
Place the two screwdrivers next to the retaining tabs so that the
flat side of the screwdriver blade contacts the retaining tab.
– Turn both screwdrivers 90°, which releases the headrest guide
retaining tabs.
– Carefully pry the headrest guide -2- out of the backrest using
a third screwdriver.
Installing
Install in reverse order of removal.
3.16
Side Cushion, Removing and Installing
Special tools and workshop equipment required
♦ Torque Wrench 1410 - VAG1410-
Removing
WARNING
Follow the General Safety Precautions when working with air‐
bags, belt tensioners and battery cut-out units (pyrotechnic
components).
Refer
to
⇒ “1.2 Safety Precautions for Pyrotechnic Components”, page
– Disconnect the battery. Refer to ⇒ Electrical Equipment; Rep.
Gr. 27 ; Battery; Battery, Disconnecting and Connecting .
– Remove the rear bench seat. Refer to
⇒ “3.7 Bench Seat/Single Seat, Removing and Installing”,
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст