Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 434
Installing
Install in reverse order of removal while paying attention to the
following:
– Check body openings -arrow- for deformations.
– In the case of deformation, readjust the panel with a plastic
hammer.
Note
Remaining minor deformation is permissible.
– Lift the carpet -2- and press in new mounting grommets -1-
until they engage audibly in body opening -arrow-.
– Place the carpet around the grommet as illustrated.
Note
The carpet must not cover the grommet.
– Check if the wire frame is aligned in the marked area
-arrows- before installing the rear bench seat.
– If the wire frame is bent, bend it back far enough until it is re‐
aligned.
– Install the rear bench seat and push the wire hooks into the
mounting grommets.
– Make sure the wire hooks are engaged correctly in the grom‐
mets.
3.8
Rear Seat Backrest, Removing and In‐
stalling
Special tools and workshop equipment required
♦ Torque Wrench 1331 5-50Nm - VAG1331-
Removing
– Remove the rear bench seat. Refer to
⇒ “3.7 Bench Seat/Single Seat, Removing and Installing”,
.
– Remove the seat belt latch with the right rear belt end fitting.
Refer to
⇒ “1.15 Rear Seat Belt Latch, Removing and Installing”, page
– Remove the cover -1- from the center support -2-.
– Remove the bolt -2-.
– Equipment levels with pass-through: open the pass through
door, and fold forward.
– Fold the rear securing clip -1- in direction of -arrow A-, disen‐
gage at the front from the center support -arrow B- and re‐
move.
Note
To improve clarity, the left rear seat backrest 1/3 is not shown.
– Lift the rear seat backrest -2- out of the center support -3- and
pull it out toward the center of the vehicle out of its outer
mounts -1- -arrows-.
– Remove rear seat backrest from the vehicle.
Installing
– In a vertical installation position, slide the rear seat backrest
-2- onto the outer mounting pins -1-.
– Place the rear seat backrest -2- in the center support -3-.
Installation is performed in reverse order of the removal.
Tightening Specifications
♦ Refer to
3.9
Locking Mechanism Trim, Removing
and Installing
Special tools and workshop equipment required
♦ Trim Removal Wedge - 3409-
♦ Hook - T10538-
Removing
Note
Due to the limited amount of space near the “locking mechanism
trim”, it is helpful to work with a second technician.
– Remove the respective rear headrest. Refer to
⇒ “3.14 Headrest, Removing and Installing”, page 390
.
– Using a screwdriver, unhook the side and upper backrest cov‐
er molding strip near the trim from the backrest.
– Using the Trim Removal Wedge - 3409- , carefully push the
cover outward at the side of the trim -2-.
– Using a light, determine the position of the respective release
tab -1-.
– Carefully bend the respective release tab -1- outward using
the Hook - T10538- .
– After both release tabs -1- have been bent outward, pull the
trim upward in direction of -arrow- and remove.
Installing
Install in reverse order of removal while paying attention to the
following:
– After installing the trim, the rear seat backrest locking mech‐
anism must function easily.
3.10
Rear Seat Backrest Locking Mecha‐
nism, Removing and Installing
Special tools and workshop equipment required
♦ Torque Wrench 1331 5-50Nm - VAG1331-
Removing
– Remove the locking mechanism trim. Refer to
– Only loosen the cover in the locking mechanism area. Refer
to
⇒ “2.4 Rear Seat Backrest Cover and Cushion, Removing and
Wagon
– Remove the seat-side release cable from the locking mecha‐
nism -1-. Refer to
.
Continuation for All Vehicles
– Remove the bolts -2-.
– Remove the locking mechanism -1- from the backrest frame.
Installing
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
⇒ “3.3 Overview - Locking Mechanism”, page 379
3.11
Pass-Through Cover Frame, Removing
and Installing
Special tools and workshop equipment required
♦ Trim Removal Wedge - 3409-
♦ Trim Release Lever - T10039-
♦ Hook Tool - T40207-
Removing
– Fold down the center armrest and open the pass-through door.
– Unclip the trim -1- from the rear seat backrest using the Trim
Removal Wedge - 3409- -arrows-.
– Use the Hook Tool - T40207- to remove the retaining tabs
-2- alternating between the sides.
– Pry off the cover frame -2- using the Trim Release Lever -
T10039- from the rear seat backrest -1- in direction of
-arrow A-.
– Continue prying off starting at the upper left corner in direction
of -arrow B-.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст