Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 364
– Sill panel strip, removing and installing. Refer to
⇒ “5.10.1 Sill Panel Strip, Removing and Installing, 2-Door
.
Continuation for All Vehicles
– Remove the front belt end fitting. Refer to
⇒ “1.11.3 Front Belt End Fitting, Removing and Installing, with
Belt End Fitting Tensioner”, page 117
– Remove the front seat belt guide. Refer to
⇒ “1.9 Front Seat Belt Guide, Removing and Installing”, page
.
– Remove the bolt -1-.
– Remove the seat belt guide -2- and seat belt webbing.
WARNING
Before handling pyrotechnic components (for example, dis‐
connecting the connector), the person handling it must “dis‐
charge static electricity”. This can be done by touching the door
striker pin, for example.
Vehicles without Reversible Belt Tensioner
– Release the connector lock with a small screwdriver in direc‐
tion of -arrow-, and remove the connector for the belt tensioner
igniter 1 -item 1-.
– If equipped, release and remove the second connector from
the front automatic belt retractor -2- in the same way.
– Remove the bolt -3- and the automatic belt retractor -2- from
the mount.
Vehicles with Reversible Belt Tensioner
– Release and disconnect the connectors -2 and 5-.
– Remove the bolts -1 and 4- and then remove the automatic
belt retractor -3- from the mount.
Installing
WARNING
♦ Observe the safety precautions for pyrotechnical compo‐
nents. Refer to
⇒ “1.2 Safety Precautions for Pyrotechnic Components”,
♦ Before handling pyrotechnic components (for example,
connecting the connector), the person handling it must
“discharge static electricity”. This can be done by touching
the door striker pin, for example.
Install in reverse order of removal while paying attention to the
following:
– If parts of the seat belt system are removed due to an accident,
replace the belt system bolts.
Note
Make sure the connectors are pushed in all the way and that they
engage audibly.
– Insert the automatic belt retractor with the anti-twist mecha‐
nism -1- in the mount -2- -arrow- and tighten the bolt.
WARNING
The ignition must be on when connecting the battery. If pyro‐
technic components (for example, airbag, belt tensioner) are
not repaired correctly, they may deploy unintentionally after
connecting battery. There must not be anyone inside the ve‐
hicle when connecting the battery.
– Connect the battery ground cable with the ignition turned on.
Refer to ⇒ Electrical Equipment; Rep. Gr. 27 ; Battery; Bat‐
tery, Disconnecting and Connecting .
WARNING
If the ignition is not switched on after the battery is reconnected
- “indicator lamps in the instrument cluster do not light up” - the
ignition (key/button) may only be switched on when the driver
seat is positioned all the way back.
Tightening Specifications
♦ Refer to
⇒ “1.2.3 Overview - Front Three-Point Seat Belt, with Belt End
1.8
Rear Three-Point Seat Belt, Removing
and Installing
⇒ “1.8.1 Rear Three-Point Seat Belt, Removing and Installing, 2-
Door Sedan, without Belt Tensioner”, page 106
⇒ “1.8.2 Rear Three-Point Seat Belt, Removing and Installing, 2-
Door Sedan, with Belt Tensioner”, page 107
⇒ “1.8.3 Rear Three-Point Seat Belt, Removing and Installing, 4-
Door Sedan, without Belt Tensioner”, page 108
⇒ “1.8.4 Rear Three-Point Seat Belt, Removing and Installing, 4-
Door Sedan, with Belt Tensioner”, page 109
⇒ “1.8.5 Rear Three-Point Seat Belt, Removing and Installing,
Wagon without Belt Tensioner”, page 110
⇒ “1.8.6 Rear Three-Point Seat Belt, Removing and Installing,
Wagon with Belt Tensioner”, page 111
⇒ “1.8.7 Rear Three Point Seat Belt in Center, Removing and
1.8.1
Rear Three-Point Seat Belt, Removing
and Installing, 2-Door Sedan, without
Belt Tensioner
Removing
– Remove the rear shelf compartment. Refer to
⇒ “6.9 Rear Shelf Compartment, Removing and Installing”,
– Remove the outer rear belt end fitting. Refer to
⇒ “1.12 Rear Outer Belt End Fitting, Removing and Installing”,
– Remove the bolt -1-.
– Remove the automatic belt retractor -2- from the mount.
Installing
Install in reverse order of removal while paying attention to the
following:
– If parts of the seat belt system are removed due to an accident,
replace the belt system bolts.
Tightening Specifications
♦ Refer to
1.8.2
Rear Three-Point Seat Belt, Removing
and Installing, 2-Door Sedan, with Belt
Tensioner
Removing
WARNING
♦ Observe the safety precautions for pyrotechnical compo‐
nents. Refer to
⇒ “1.2 Safety Precautions for Pyrotechnic Components”,
♦ Observe the disposal regulations for pyrotechnical com‐
ponents. Refer to
⇒ “1.3 Airbag, Belt Tensioner and Battery Cut-Out Units,
Storing, Transporting and Disposing (Pyrotechnic Com‐
– Disconnect the battery ground cable with the ignition turned
on. Refer to ⇒ Electrical Equipment; Rep. Gr. 27 ; Battery;
Battery, Disconnecting and Connecting .
– Remove the rear shelf compartment. Refer to
⇒ “6.9 Rear Shelf Compartment, Removing and Installing”,
.
– Remove the outer rear belt end fitting. Refer to
⇒ “1.12 Rear Outer Belt End Fitting, Removing and Installing”,
.
WARNING
Electrostatic discharges can lead to unintended deployment of
the airbag. Therefore the technician must discharge static elec‐
tricity from the body before separating the ignition and ground
wiring. This is done, for example, by briefly touching the body
or door striker.
– Disconnect the wiring harness and unclip the connector -1-.
– Remove the bolt -2-.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст