Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 618
– Insert a large screwdriver in the groove on the locking mech‐
anism and turn 90° in the direction of -arrow-.
– Pull the cable from the selector mechanism and remove.
Installing
Note
♦
Do not bend or kink the selector lever cable.
♦
Do not lubricate the selector lever cable.
♦
After installing check the selector lever cable for ease of move‐
ment.
• The selector mechanism selector lever is in the “N” position.
The cable in the selector mechanism can only be locked in this
position.
– Guide the cable in the selector mechanism until it is visible
through the locking mechanism -arrow-.
– Turn the locking mechanism in the direction of -arrow- 90° with
a large screwdriver.
– The cable is correctly locked when the grooves on the locking
mechanism are at a right angle to the cable.
– Install new clip -arrow- and replace the plugs.
– Insert the selector lever cable -1- in the cable bracket -4- and
install a new clip -5-.
– Press the selector lever cable carefully onto the selector lever.
If removed, install the cable bracket -4- with the bolts -arrows- on
the transmission.
– Engage the selector lever cable in the bracket -2- clip -3-.
– Install the heat shield under the selector mechanism. Refer to
⇒ Body Exterior; Rep. Gr. 66 ; Molding/Trim/Extensions/Trim
Panels; Floor Heat Shield, Removing and Installing .
– Adjust the selector lever cable. Refer to
⇒ “2.4 Selector Lever Cable, Checking and Adjusting”,
.
– Check the selector mechanism. Refer to
⇒ “2.8 Gearshift Mechanism, Checking”, page 36
.
– Install the air filter housing. Refer to ⇒ Engine Mechanical,
Fuel Injection and Ignition; Rep. Gr. 24 ; Air Filter; Air Filter
Housing, Removing and Installing .
Tightening Specifications
♦ Refer to
⇒ “2.1 Overview - Selector Mechanism”, page 19
2.4
Selector Lever Cable, Checking and Ad‐
justing
Special tools and workshop equipment required
♦ Torque Wrench 5-50Nm - VAG1331-
Short Description
To check the selector lever cable for ease of movement, remove
it from the transmission and position the removed end so it does
not make contact anywhere.
Then selector lever is moved and the selector lever cable installed
again on the transmission.
After that, selector lever cable must be adjusted. Refer to
Do not grease the selector lever cable connection!
Checking
– Move the selector lever into »P«.
– Loosen the bolt -2- on the selector lever cable -1-.
– Pry the selector lever cable -1- off the selector lever -3-, for
example, using a wrench.
– Disengage the selector lever cable -1- from the bracket -2- clip
-3-.
– Remove the cable bracket -4- from the transmission to do this
remove the bolts -arrows-.
Note
Do not remove the clip -5-.
– Move the selector lever from »P« through »S« and back to »P«
several times.
• The selector lever and the selector lever cable must have ease
of movement at the same time.
– Install the selector lever cable again.
– Adjust the selector lever cable. Refer to
Selector Lever Cable Must Always be Adjusted If:
♦ The selector lever cable was removed from the transmission.
♦ The engine and/or transmission were removed and installed.
♦ Parts of subframe mount were removed and installed.
♦ The selector lever cable itself or the selector mechanism was
removed and installed.
♦ Engine/transmission positions changes, for example, were in‐
stalled free of tension.
Adjusting:
– Move the selector lever into “P”.
• The adjustment screw -2- must be »loosened«.
– Move the selector lever -3- on the transmission into “P” (push
the gearshift lever to the rear).
WARNING
The parking lock must be engaged.
– From »underneath the vehicle«, rotate both front wheels in the
same direction and at the same time until the parking lock au‐
dibly engages.
• The parking lock is engaged when it is not possible to rotate
both front wheels in the same direction at the same time.
– Tap the handle on the selector lever back and forth gently but
do not move it out of “P”.
This places the selector lever cable core in its optimal position.
– Tighten the bolt -2-.
This ends the adjustment.
Tightening Specifications
♦ Refer to
⇒ “2.1 Overview - Selector Mechanism”, page 19
2.5
Emergency Release from P
Do Not Remove the Handle.
– Press the brake or set the parking brake.
– Open the storage compartment door.
– Grab under the cover by hand and unclip by pulling upward.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст