Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 617
– Move the selector lever into “P”.
– Remove the selector lever handle. Refer to
⇒ “2.6 Selector Lever Handle, Removing and Installing”, page
. Disconnect the connector -2- from the cover while doing
this.
– Disconnect the connector -1- from the selector mechanism to
the vehicle wiring harness.
– Remove the center console. Refer to ⇒ Body Interior; Rep.
Gr. 68 ; Center Console; Overview - Center Console .
– Remove the air guide channel from the center console. Refer
to ⇒ Heating, Ventilation and Air Conditioning; Rep. Gr. 87 ;
Air Routing; Overview - Air Routing and Air Distribution in Pas‐
senger Compartment .
– Remove the bracket -2-, to do this remove the left and right
bolts -1-.
– Position the selector lever on the selector mechanism in the
“N” position. The cable can only be loosened in this position.
– Remove the center tunnel heat shield under the selector
mechanism. Refer to ⇒ Body Exterior; Rep. Gr. 66 ; Molding/
Trim/Extensions/Trim Panels; Floor Heat Shield, Removing
and Installing .
– Remove the plugs, and remove the clip -arrow-.
Replace the clip after removing.
– Insert a large screwdriver in the groove on the locking mech‐
anism and turn 90° in the direction of -arrow-.
– Remove the cable from the selector mechanism.
– Remove the bracket -A-, if equipped.
– Remove the nuts -arrows- in the vehicle interior.
– Remove the selector mechanism -B- with the gearshift hous‐
ing downward.
Installing
Install in reverse order of removal. Note the following:
A second technician will be needed for inserting the selector lever
cable from the passenger compartment into the engine compart‐
ment.
Note
♦
Do not bend or kink the selector lever cable.
♦
Do not lubricate the selector lever cable.
♦
After installation, the selector lever cable movement must be
checked and adjusted.
• The selector mechanism selector lever is in the “N” position.
The cable can only be locked in this position.
– Guide the cable in the selector mechanism until it is visible
through the locking mechanism -arrow-.
– Turn the locking mechanism in the direction of -arrow- 90° with
a large screwdriver.
– The cable is correctly locked when the grooves on the locking
mechanism are at a right angle to the cable.
– Install new clip -arrow- and replace the plugs.
– Install the heat shield under the selector mechanism. Refer to
⇒ Body Exterior; Rep. Gr. 66 ; Molding/Trim/Extensions/Trim
Panels; Floor Heat Shield, Removing and Installing .
– Install the bracket -2- if equipped. Refer to ⇒ Body Interior;
Rep. Gr. 68 ; Center Console; Center Console, Removing and
Installing .
– Install the air guide channel from the center console. Refer to
⇒ Heating, Ventilation and Air Conditioning; Rep. Gr. 87 ; Air
Routing; Overview - Air Routing and Air Distribution in Pas‐
senger Compartment .
– Install the center console. Refer to ⇒ Body Interior; Rep. Gr.
68 ; Center Console; Center Console, Removing and Instal‐
ling .
– Install the selector lever handle. Refer to
⇒ “2.6 Selector Lever Handle, Removing and Installing”, page
.
– Selector lever cable, adjusting. Refer to
⇒ “2.4 Selector Lever Cable, Checking and Adjusting”,
– Check the selector mechanism. Refer to
⇒ “2.8 Gearshift Mechanism, Checking”, page 36
Tightening Specifications
♦ Refer to
⇒ “2.1 Overview - Selector Mechanism”, page 19
2.3
Selector Lever Cable, Removing and In‐
stalling
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
Mandatory Replacement Parts
♦ Clip - Selector Lever Cable to the Cable Bracket
♦ Clip - Selector Lever Cable to the Selector Mechanism
♦ Plug - Selector Mechanism
– Remove the air filter housing. Refer to ⇒ Engine Mechanical,
Fuel Injection and Ignition; Rep. Gr. 24 ; Air Filter; Air Filter
Housing, Removing and Installing
– Disengage the selector lever cable -1- from the bracket -2- clip
-3-.
Use pliers to remove the clip -5- from the cable bracket -4-. Do
not use a sharp-edged lever. Otherwise the selector lever cable
could get damaged.
Note
♦
Always replace the clip on the selector lever cable.
♦
It is better to remove the cable bracket -4- together with the
selector lever cable -1- from the transmission -arrow-.
♦
If the selector lever cable is replaced, the cable bracket -4-
must be replaced.
– Pry the selector lever cable -1- off the selector lever -3-, for
example, using a wrench.
The adjusting screw -2- must not be loosened.
Caution
Danger of damaging the selector lever cable.
♦ Push the selector lever cable to the rear and out of the
cable bracket. The selector lever cable is guided out of the
cable bracket when removing the selector mechanism.
– Lift the vehicle.
– Remove the center tunnel heat shield under the selector
mechanism. Refer to ⇒ Body Exterior; Rep. Gr. 66 ; Molding/
Trim/Extensions/Trim Panels; Floor Heat Shield, Removing
and Installing .
– Remove the plugs, and remove the clip -arrow-.
Replace the clip after removing.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст