Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 616
11 - Selector Lever Cable
❑ Removing and installing. Refer to
⇒ “2.3 Selector Lever Cable, Removing and Installing”, page 27
12 - Clips
❑ Secures the selector lever cable on the cable bracket
❑ Replace after removing
13 - Bolt
❑ 20 Nm
14 - Clips
❑ Replace after removing
2.2
Selector Mechanism, Removing and In‐
stalling
⇒ “2.2.1 Shift Mechanism with Selector Lever Cable, Removing
and Installing”, page 21
⇒ “2.2.2 Selector Mechanism without Selector Lever Cable, Re‐
moving and Installing”, page 24
2.2.1
Shift Mechanism with Selector Lever
Cable, Removing and Installing
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
Mandatory Replacement Parts
♦ Clip - Selector Lever Cable to the Cable Bracket
♦ Clip - Selector Lever Cable to the Selector Mechanism
♦ Plug - Selector Mechanism
Short Description
Remove the center console inside the passenger compartment.
It is necessary to remove the heat shield under the vehicle.
Removing
– Move the selector lever into “P”.
– Remove the selector lever handle. Refer to
⇒ “2.6 Selector Lever Handle, Removing and Installing”, page
. Disconnect the connector -2- from the cover while doing
this.
– Disconnect the connector -1- from the selector mechanism to
the vehicle wiring harness.
– Remove the center console. Refer to ⇒ Body Interior; Rep.
Gr. 68 ; Center Console; Center Console, Removing and In‐
stalling .
– Remove the air guide channel from the center console. Refer
to ⇒ Heating, Ventilation and Air Conditioning; Rep. Gr. 87 ;
Air Routing; Overview - Air Routing and Air Distribution in Pas‐
senger Compartment .
– Remove the bracket -2-, to do this remove the left and right
bolts -1-.
– Remove the air filter housing. Refer to ⇒ Engine Mechanical,
Fuel Injection and Ignition; Rep. Gr. 24 ; Air Filter; Air Filter
Housing, Removing and Installing
– Disengage the selector lever cable -1- from the bracket -2- clip
-3-.
Use pliers to remove the clip -5- from the cable bracket -4-. Do
not use a sharp-edged lever. Otherwise the selector lever cable
could get damaged.
Note
♦
Always replace the clip on the selector lever cable.
♦
It is better to remove the cable bracket -4- together with the
selector lever cable -1- from the transmission -arrow-.
♦
If the selector mechanism is replaced with the selector lever
cable the cable bracket -4- must be replaced.
– Pry the selector lever cable -1- off the selector lever -3-, for
example, using a wrench.
The adjusting screw -2- must not be loosened.
Caution
Danger of damaging the selector lever cable.
♦ Push the selector lever cable to the rear and out of the
cable bracket. Guide the selector lever cable out of the
cable bracket when removing the selector mechanism.
– Lift the vehicle.
– Remove the center tunnel heat shield under the selector
mechanism. Refer to ⇒ Body Exterior; Rep. Gr. 66 ; Molding/
Trim/Extensions/Trim Panels; Floor Heat Shield, Removing
and Installing .
– Remove the bracket -A-, if equipped.
– Remove the nuts -arrows- in the vehicle interior.
– Remove the selector mechanism -B- with the selector lever
cable and selector housing downward.
Installing
Install in reverse order of removal. Note the following:
Note
♦
Do not bend or kink the selector lever cable.
♦
Do not lubricate the selector lever cable.
♦
After installation, the selector lever cable movement must be
checked and adjusted.
– Insert the selector lever cable -1- in the cable bracket -4- and
install a new clip -5-.
– Press the selector lever cable carefully onto the selector lever.
If removed, install the cable bracket -4- with the bolts -arrows- on
the transmission.
– Engage the selector lever cable in the bracket -2- clip -3-.
– Install the heat shield under the selector mechanism. Refer to
⇒ Body Exterior; Rep. Gr. 66 ; Molding/Trim/Extensions/Trim
Panels; Floor Heat Shield, Removing and Installing .
– Install the bracket -2-. Refer to ⇒ Body Interior; Rep. Gr. 68 ;
Center Console; Center Console, Removing and Installing .
– Install the air guide channel from the center console. Refer to
⇒ Heating, Ventilation and Air Conditioning; Rep. Gr. 87 ; Air
Routing; Overview - Air Routing and Air Distribution in Pas‐
senger Compartment .
– Install the center console. Refer to ⇒ Body Interior; Rep. Gr.
68 ; Center Console; Center Console, Removing and Instal‐
ling .
– Install the selector lever handle. Refer to
⇒ “2.6 Selector Lever Handle, Removing and Installing”, page
– Selector lever cable, adjusting. Refer to
⇒ “2.4 Selector Lever Cable, Checking and Adjusting”,
.
– Check the selector mechanism. Refer to
⇒ “2.8 Gearshift Mechanism, Checking”, page 36
– Install the air filter housing. Refer to ⇒ Engine Mechanical,
Fuel Injection and Ignition; Rep. Gr. 24 ; Air Filter; Air Filter
Housing, Removing and Installing .
Tightening Specifications
♦ Refer to
⇒ “2.1 Overview - Selector Mechanism”, page 19
2.2.2
Selector Mechanism without Selector
Lever Cable, Removing and Installing
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
Mandatory Replacement Parts
♦ Clip - Selector Lever Cable to the Selector Mechanism
♦ Plug - Selector Mechanism
Short Description
Remove the center console inside the passenger compartment.
It is necessary to remove the heat shield under the vehicle.
Removing
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст