Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 459
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
Mandatory Replacement Parts
♦ Clamp - Shift Handle
Short Description:
The handle is removed together with the shift cover.
Removing
– Move the selector lever into “D”.
It is not necessary to pull out the button -arrow- manually. The
push button locks in the installation position by itself when the
handle is removed.
– Open the storage compartment door.
– Grab and under the shift cover by hand and pulling upward
unclip the cover.
– Disconnect the connector.
– Cut the clamp under the boot -arrow- with a side cutter.
– Pull the handle up without pressing the button.
Note
Do not push the button once the handle has been removed oth‐
erwise it will not be possible to remove the handle again.
Installing
Install in reverse order of removal. Note the following:
• The selector lever is in the “D” position.
Note
♦
There is the possibility that the button can be pressed into the
handle. Never install the handle when the button is pressed in.
♦
Move the button in the installation position. Refer to
⇒ “2.4 Button in Handle, Moving Into Installation Position”,
♦
A new handle is delivered with an assembly fastener. Pull out
the safety catch in direction of -arrow- just before installing the
new handle.
– Install the handle with a new clamp -arrow-. Do not clamp the
clamp yet.
– Press the button after installing it.
Note
If the button stays in the handle after being pressed, this means
it was installed incorrectly. If this happens, remove the handle
again and move the button in the installation position again. Refer
to
⇒ “2.4 Button in Handle, Moving Into Installation Position”,
– If the button after being pressed return to its starting position,
the clamp can be clamp off using Hose Clamp Pliers -
VAG1275A- .
– Connect the connector.
– Clip on the cover.
2.4
Button in Handle, Moving Into Installa‐
tion Position
If the button was pushed in by mistake, the installed position can
be set again.
There are two ways to move the button into the installation posi‐
tion, “with” or “without” assembly fastener. The following de‐
scribes both ways.
Moving the Handle “with” an Assembly Fastener into the Instal‐
lation Position:
Make sure the assembly fastener has an eye -arrow- at the front.
Other assembly fasteners cannot be used.
– Press the button and push the assembly fastener (with the
eye) -arrow- all the way in until it latches into place. Then re‐
lease the button. The button locks into the installation position
when the assembly fastener is pulled out.
Moving the Handle “without” an Assembly Fastener into the In‐
stallation Position:
– Remove the trim -A- from the handle.
– Push the small lever -1- into the groove -2- with a screwdriver.
This pushes the button -3- into the installation position.
-I- the button is in the pressed position
-II- the button is in the installation position
Note
♦
Push the lever into the groove and no further.
♦
Install the trim back onto the selector mechanism only after the
handle is installed. This way it is possible to see if the small
lever fits into the pull rod when the button is pushed.
2.5
Selector Mechanism, Removing and In‐
stalling
⇒ “2.5.1 Shift Mechanism with Selector Lever Cable, Removing
and Installing”, page 55
⇒ “2.5.2 Gearshift Mechanism without Selector Lever Cable, Re‐
moving and Installing, ZF”, page 57
⇒ “2.5.3 Shift Lever Mechanism without Selector Lever Cable,
Removing and Installing, ECS”, page 60
2.5.1
Shift Mechanism with Selector Lever
Cable, Removing and Installing
Short Description
Remove the center console inside the passenger compartment.
It is necessary to remove the heat shield under the vehicle.
Removing
– Remove the selector lever handle. Refer to
⇒ “2.3 Selector Lever Handle, Removing and Installing”, page
.
– Remove the center console. Refer to ⇒ Body Interior; Rep.
Gr. 68 ; Center Console; Center Console, Removing and In‐
stalling .
– Remove the air guide channel from the center console. Refer
to ⇒ Heating, Ventilation and Air Conditioning; Rep. Gr. 87 ;
Air Routing; Overview - Air Routing and Air Distribution in Pas‐
senger Compartment .
– Remove left and right bolts -1- and bracket -2-.
– Disconnect the connector from the selector mechanism to the
vehicle wiring harness.
– Remove the air filter housing:
♦ Gasoline engine. Refer to ⇒ Engine Mechanical, Fuel Injec‐
tion and Ignition; Rep. Gr. 24 ; Air Filter; Air Filter Housing,
Removing and Installing .
♦ Diesel engine. Refer to ⇒ Rep. Gr. 23 ; Air Filter; Air Filter
Housing, Removing and Installing .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст