Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 460
Loosen the adjusting screw -arrow-.
– Remove the lock washers -A and B-. The lock washers must
later be replaced when adjusting selector lever cable.
Use pliers to remove the lock washer -B-. Do not use a sharp-
edged lever. Otherwise the selector lever cable could get dam‐
aged.
– Remove the center tunnel heat shield under the gearshift
mechanism. Refer to ⇒ Body Exterior; Rep. Gr. 66 ; Molding/
Trim/Extensions/Trim Panels; Floor Heat Shield, Removing
and Installing .
– Remove the bracket -A-, if equipped.
– Remove the nuts -arrows- in the vehicle interior.
– Remove the selector mechanism -B- with the selector lever
cable and selector housing downward.
Installing
Install in reverse order of removal. Note the following:
Note
♦
Do not bend or kink the selector lever cable.
♦
Do not lubricate the selector lever cable.
♦
After installation, the selector lever cable movement must be
checked and adjusted.
– Install the heat shield under the gearshift mechanism. Refer
to ⇒ Body Exterior; Rep. Gr. 66 ; Molding/Trim/Extensions/
Trim Panels; Floor Heat Shield, Removing and Installing .
– Install the bracket -2-. Refer to ⇒ Body Interior; Rep. Gr. 68 ;
Center Console; Center Console, Removing and Installing .
– Install the air guide channel from the center console. Refer to
⇒ Heating, Ventilation and Air Conditioning; Rep. Gr. 87 ; Air
Routing; Overview - Air Routing and Air Distribution in Pas‐
senger Compartment .
– Install the center console. Refer to ⇒ Body Interior; Rep. Gr.
68 ; Center Console; Center Console, Removing and Instal‐
ling .
– Install the selector lever handle. Refer to
⇒ “2.3 Selector Lever Handle, Removing and Installing”, page
.
– Adjust the selector lever cable. Refer to
⇒ “2.8 Selector Lever Cable, Checking and Adjusting”,
– Check the selector mechanism. Refer to
⇒ “2.7 Gearshift Mechanism, Checking”, page 67
– Install the air filter housing:
♦ Gasoline engine. Refer to ⇒ Engine Mechanical, Fuel Injec‐
tion and Ignition; Rep. Gr. 24 ; Air Filter; Air Filter Housing,
Removing and Installing .
♦ Diesel engine. Refer to ⇒ Rep. Gr. 23 ; Air Filter; Air Filter
Housing, Removing and Installing .
Tightening Specifications
♦ Selector mechanism to the body. Refer to
⇒ “2.1 Overview - Selector Mechanism”, page 47
2.5.2
Gearshift Mechanism without Selector
Lever Cable, Removing and Installing,
ZF
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
Mandatory Replacement Parts
♦ Lock Washer - Locking Mechanism
Short Description
Remove the center console inside the passenger compartment.
It is necessary to remove the heat shield under the vehicle.
Removing
– Remove the selector lever handle. Refer to
⇒ “2.3 Selector Lever Handle, Removing and Installing”, page
.
– Remove the center console. Refer to ⇒ Body Interior; Rep.
Gr. 68 ; Center Console; Center Console, Removing and In‐
stalling .
– Remove the air guide channel from the center console. Refer
to ⇒ Heating, Ventilation and Air Conditioning; Rep. Gr. 87 ;
Air Routing; Overview - Air Routing and Air Distribution in Pas‐
senger Compartment .
– Remove the bracket -2-, to do this remove the left and right
bolts -1-.
– Disconnect the connector from the selector mechanism to the
vehicle wiring harness.
– Position the selector lever on the selector mechanism in the
“N” position. The cable can only be loosened in this position.
– Remove the center tunnel heat shield under the gearshift
mechanism. Refer to ⇒ Body Exterior; Rep. Gr. 66 ; Molding/
Trim/Extensions/Trim Panels; Floor Heat Shield, Removing
and Installing .
– Remove the plugs, and remove the lock washer -arrow-.
Always replace the lock washer.
– Insert a large screwdriver into the grooves on the locking
mechanism and turn 90° in the direction of the -arrow-.
– Remove the cable from the selector mechanism.
– Remove the bracket -A-, if equipped.
– Remove the nuts -arrows- in the vehicle interior.
– Remove the selector mechanism -B- with the gearshift hous‐
ing downward.
Installing
Install in reverse order of removal. Note the following:
Note
♦
Do not bend or kink the selector lever cable.
♦
Do not lubricate the selector lever cable.
♦
After installation, the selector lever cable movement must be
checked and adjusted.
• The selector lever for the gearshift mechanism is in the “N”
position. The cable can only be locked in this position.
– Guide the cable into the selector mechanism in direction of
-arrow- until the locking mechanism -arrow- is visible.
– Turn the locking mechanism 90° in the direction of the
-arrow- with a large screwdriver.
– The cable is correctly locked when the grooves on the locking
mechanism are at a right angle to the cable.
– Install new lock washer -arrow- and replace the plugs.
– Install the heat shield under the shift lever mechanism. Refer
to ⇒ Body Exterior; Rep. Gr. 66 ; Molding/Trim/Extensions/
Trim Panels; Floor Heat Shield, Removing and Installing .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст