Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 391
Removing
– First loosen the trim molding -1- from the retainers using the
Trim Removal Wedge - 3409- in direction of -arrows A-.
– Then slide the trim molding -1- outward in direction of
-arrow B- and remove it.
Installing
Note
Check all the fasteners for damage and replace if necessary.
Install in reverse order of removal.
3.4
Light Switch Trim, Removing and Instal‐
ling
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Removing
– Remove the Rotary Light Switch - EX1- . Refer to ⇒ Electrical
Equipment; Rep. Gr. 96 ; Controls; Component Location
Overview - Instrument Panel Controls .
– Remove the bolt -2-.
– Remove the light switch trim -1- from the instrument panel to‐
ward the rear.
– If installed, release and disconnect the connector from the
Headlamp Range Control Adjuster - E102- .
Installing
Note
Check all the fasteners for damage and replace if necessary.
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
⇒ “3.1 Overview - Instrument Panel”, page 210
3.5
Instrument Cluster Trim, Removing and
Installing
Special tools and workshop equipment required
♦ Trim Removal Wedge - 3409-
Removing
– Remove the side instrument panel vent on the driver side. Re‐
fer to
⇒ “3.7 Instrument Panel Vent, Removing and Installing”, page
.
– Loosen the center vent, but do not completely remove it. Refer
to
⇒ “3.7 Instrument Panel Vent, Removing and Installing”, page
.
– Loosen the gap cover near the instrument cluster trim, but do
not completely remove it. Refer to
⇒ “1.10 Instrument Cluster Gap Cover, Removing and Instal‐
.
– Unclip the instrument cluster trim -1- from the instrument panel
using the Trim Removal Wedge - 3409- .
– Remove the instrument cluster trim -1- from the instrument
cluster -2-.
Installing
Note
Check all the fasteners for damage and replace if necessary.
Install in reverse order of removal.
3.6
Instrument Panel, Removing and Instal‐
ling
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Removing
– Remove the center console. Refer to
⇒ “3.8 Center Console, Removing and Installing”, page 59
– Move the front seats all the way back.
– Disconnect the battery ground cable. Refer to ⇒ Electrical
Equipment; Rep. Gr. 27 ; Battery; Battery, Disconnecting and
Connecting .
– Remove the driver side airbag. Refer to
⇒ “5.2 Airbag Unit with Igniter, Removing and Installing”, page
– Remove the steering wheel. Refer to ⇒ Suspension, Wheels,
Steering; Rep. Gr. 48 ; Steering Wheel; Steering Wheel, Re‐
moving and Installing .
– Remove the steering column switch. Refer to ⇒ Electrical
Equipment; Rep. Gr. 94 ; Steering Column Switch Module;
Steering Column Switch Module, Removing and Installing .
– Remove the light switch trim. Refer to
⇒ “3.4 Light Switch Trim, Removing and Installing”,
.
– Remove the instrument panel cover on the driver side. Refer
to
⇒ “1.9 Driver Side Instrument Panel Cover, Removing and In‐
– Remove the glove compartment. Refer to
⇒ “1.17 Glove Compartment, Removing and Installing”,
– Remove the center vent. Refer to
⇒ “3.7 Instrument Panel Vent, Removing and Installing”, page
– Remove the instrument cluster. Refer to ⇒ Electrical Equip‐
ment; Rep. Gr. 90 ; Instrument Cluster; Instrument Cluster -
KX2- , Removing and Installing .
– Remove the Front Information Display Control Head - J685- .
Refer to ⇒ Communication; Rep. Gr. 91 ; Infotainment Sys‐
tem; Infotainment System Display, Removing and Installing .
– Remove the left and right triangular window trim panel. Refer
to
⇒ “5.12 A-Pillar Trim Panel, Removing and Installing”,
– If equipped, remove the Sunlight Photo Sensor - G107- . Refer
to ⇒ Heating, Ventilation, and Air Conditioning; Rep. Gr. 87 ;
Additional Components for Control and Regulation; Sunlight
Photo Sensor G107, Removing and Installing .
– Disconnect the front passenger airbag connector. Refer to
⇒ “6.2 Front Passenger Airbag Unit with Igniter, Removing and
.
– Remove the screw -2- for securing the instrument panel -1-
from the central tube on the front passenger side.
– Remove the screws -3- for securing the instrument panel -1-
from the central tube in the center.
– Remove the screws -4 and 5- for securing the instrument panel
-1- from the central tube on the right side.
– Remove the screws -2 through 4- for securing the instrument
panel -1- from the central tube on the left side.
– Remove the screw -5- for securing the instrument panel -1-
from the central tube on the driver side.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст