Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 389
– Turn/release the clip -1- 90° in direction of the -arrow- (
1
/4 of
a turn) using TORX
®
T30.
– Loosen the clips -2- for the door trim panel -1- out of the
mounts using the Wedge Set - T10383- . The clip -3- was al‐
ready released.
– Remove the door trim panel -1- vertically from the window
shaft strip.
– Depending on the vehicle equipment level, disconnect the
connectors from the door trim panel -1-.
– Disconnect the cable -1- from the interior door mechanism.
Installing
Note
Check all the fasteners for damage and replace if necessary.
Install in reverse order of removal while paying attention to the
following:
– Insert the clips into the rear door trim panel.
Caution
Before installing the door trim panel, make sure that the locking
mechanism of all clip connections are in -position 1-.
It is not possible to install the door trim panel correctly if the
clips are in the -2 position-.
Pro
te
c
t
ed
b
y
co
p
y
rig
h
t.
C
o
p
y
in
g
fo
r
pr
iv
a
t
e
o
r
c
o
m
m
e
r
c
ia
l
p
u
rp
o
s
e
s
,
i
n
p
a
rt
r i
n
w
h
o
le
,
is
n
o
t
p
e
r
m
it
t
e
d
u
n
l
e
s
s
a
ut
ho
r
i
s
ed
b
y
V
olk
sw
a
ge
n AG
.
V
olk
s
w
a
g
en
AG do
es
n
ot g
uar
ante
e
or a
c
c
ep
t
a
ny
li
a
b
i
li
t
y
w
ith
r
e
s
p
e
c
t
t
o
th
e
c
o
rr
e
c
t
n
e
s
s
o
f
in
fo
r
m
a
tio
n
in
th
is
d
o
c
um
en
t.
C
o
py
rig
ht b
y
V
olk
sw
a
ge
n
A
G.
Tightening Specifications
♦ Refer to
⇒ “2.1 Overview - Rear Door Trim Panel”, page 202
2.3
Interior Door Mechanism, Removing
and Installing
The interior door mechanism is clipped into the trim molding for
the door trim panel.
Note
The removal and installation of the driver side trim molding is de‐
scribed. The removal and installation for the front passenger side
is identical.
Removing
– Remove the rear door trim panel. Refer to
⇒ “2.2 Rear Door Trim Panel, Removing and Installing”, page
.
– Remove the trim molding. Refer to
– Carefully unclip the interior door mechanism all the way
around from the retainers in the trim molding.
Installing
Install in reverse order of removal.
2.4
Trim Molding, Removing and Installing
Note
The removal and installation of the driver side trim molding is de‐
scribed. The removal and installation for the front passenger side
is identical.
Removing
– Remove the rear door trim panel. Refer to
⇒ “2.2 Rear Door Trim Panel, Removing and Installing”, page
– Drill out the attachment points -2- for the trim molding -1- from
the door trim panel using an appropriate drill until the trim
molding starts to loosen from the door trim panel.
Caution
The door trim panel must not be damaged by drilling.
– Carefully loosen the attachment points -2- one after the other
and remove the trim molding -1- from the door trim panel.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст