Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 390
Installing
Lock washers near the trim strip: 17 mm × 7.5 mm, quantity: 7.
Allocation. Refer to the Parts Catalog.
Lock washers near the interior door mechanism: 13.4 mm × 6 mm,
quantity: 6. Allocation. Refer to the Parts Catalog.
– Insert the new trim molding -1- into the door trim panel.
– Press the lock washers -2- all the way onto the pins -3- of the
trim molding.
– Press the remaining lock washers near the interior door mech‐
anism onto the trim molding pins as described.
– Cut back the trim molding pins -3- above the lock washers
-2- so that the projecting end is a maximum of 2 mm.
– Install the rear door trim panel. Refer to
⇒ “2.2 Rear Door Trim Panel, Removing and Installing”, page
.
3
Instrument Panel
⇒ “3.1 Overview - Instrument Panel”, page 210
⇒ “3.2 Instrument Panel Side Cover, Removing and Installing”,
page 211
⇒ “3.3 Instrument Panel Decorative Trim, Removing and Instal‐
ling”, page 211
⇒ “3.4 Light Switch Trim, Removing and Installing”, page 212
⇒ “3.5 Instrument Cluster Trim, Removing and Installing”,
page 212
⇒ “3.6 Instrument Panel, Removing and Installing”, page 213
⇒ “3.7 Instrument Panel Vent, Removing and Installing”,
page 220
⇒ “3.8 Side Defroster Vent, Removing and Installing”, page 223
⇒ “3.9 Front Passenger Side Impact Absorber, Removing and In‐
3.1
Overview - Instrument Panel
1 - Side Defroster Vent
❑ Left and right
❑ Removing and instal‐
ling. Refer to
2 - Rubber Buffer
❑ Quantity: 2
❑ Pushed on the instru‐
ment panel mount under
the windshield frame
3 - Screw
❑ 1.5 Nm
4 - Sunlight Photo Sensor -
G107-
❑ Removing and instal‐
ling. Refer to ⇒ Heating,
Ventilation, and Air Con‐
ditioning; Rep. Gr. 87 ;
Additional Components
for Control and Regula‐
tion; Sunlight Photo
Sensor G107, Remov‐
ing and Installing .
5 - Instrument Panel
❑ Removing and instal‐
ling. Refer to
6 - Instrument Panel Decora‐
tive Trim
❑ Allocation. Refer to the
Parts Catalog.
❑ Removing and installing. Refer to
⇒ “3.3 Instrument Panel Decorative Trim, Removing and Installing”, page 211
.
7 - Center Vent with Front Information Display Control Head - J685- Trim
Note
Always remove the Front Informa‐
tion Display Control Head - J685-
trim together with the center vent.
❑ Removing and installing. Refer to
⇒ “3.7 Instrument Panel Vent, Removing and Installing”, page 220
8 - Instrument Cluster Trim
❑ Removing and installing. Refer to
⇒ “3.5 Instrument Cluster Trim, Removing and Installing”, page 212
9 - Rotary Light Switch - EX1-
❑ Removing and installing. Refer to ⇒ Electrical Equipment; Rep. Gr. 96 ; Controls; Rotary Light Switch
EX1, Removing and Installing .
10 - Light Switch Trim
❑ Removing and installing. Refer to
⇒ “3.4 Light Switch Trim, Removing and Installing”, page 212
.
11 - Side Instrument Panel Vent
❑ Left and right
❑ Removing and installing. Refer to
⇒ “3.7 Instrument Panel Vent, Removing and Installing”, page 220
3.2
Instrument Panel Side Cover, Removing
and Installing
Note
Removal and installation are described for the driver side instru‐
ment panel side cover. The removal and installation for the front
passenger side is identical.
Special tools and workshop equipment required
♦ Trim Removal Wedge - 3409-
Removing
– Pry off the instrument panel side cover -1- using the Trim Re‐
moval Wedge - 3409- .
– Remove the cover rearward from the A-pillar gap cover.
Installing
Note
Check all the fasteners for damage and replace if necessary.
Install in reverse order of removal.
3.3
Instrument Panel Decorative Trim, Re‐
moving and Installing
Special tools and workshop equipment required
♦ Trim Removal Wedge - 3409-
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст