Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 412
– Unclip any remaining clips in the rear lid using the Omega Clip
Tool - T40280- .
– Insert the removed clips into the trim panel -3- again.
Installing
Note
Check all the fasteners for damage and replace if necessary.
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
7
Roof Trim Panels
⇒ “7.1 Overview - Headliner”, page 297
⇒ “7.2 Roof End Strip, Removing and Installing”, page 299
⇒ “7.3 Headliner, Removing and Installing”, page 299
⇒ “7.4 Roof Reinforcement, Attaching to Body”, page 303
7.1
Overview - Headliner
⇒ “7.1.1 Overview - Headliner, Sedan”, page 297
⇒ “7.1.2 Overview - Headliner, Wagon”, page 298
7.1.1
Overview - Headliner, Sedan
1 - Headliner
❑ Allocation. Refer to the
Parts Catalog.
❑ For certain equipment
levels, it is necessary to
cut openings in the new
headliner. Refer to
❑ Removing and instal‐
ling. Refer to
.
Caution
♦
The headliner bends
easily.
♦
Replace the headliner if it
is bent.
2 - Frame
❑ Only with a sunroof
3 - Roof Reinforcement
❑ Not with a sunroof
❑ Install on the body. Re‐
fer to
4 - Roof Reinforcement
❑ Install on the body. Re‐
fer to
5 - Clip
❑ Quantity: 7
❑ Remove the clips that are still in the mounting points on the body using the Omega Clip Tool - T40280-
❑ Replace damaged or deformed retaining clips
6 - Roof End Strip
❑ Removing and installing. Refer to
7 - Clip
❑ Only with a sunroof
❑ Quantity: 15
❑ Insert in the headliner
❑ Remove any remaining clips in the frame
❑ Replace damaged or deformed retaining clips
7.1.2
Overview - Headliner, Wagon
1 - Headliner
❑ Allocation. Refer to the
Parts Catalog.
❑ For certain equipment
levels, it is necessary to
cut openings in the new
headliner. Refer to
❑ Removing and instal‐
ling. Refer to
Caution
♦
The headliner bends
easily.
♦
Replace the headliner if it
is bent.
2 - Frame
❑ Only with a sunroof
3 - Roof Reinforcement
❑ Not with a sunroof
❑ Install on the body. Re‐
fer to
.
4 - Roof Reinforcement
❑ Not with a sunroof
❑ Install on the body. Re‐
fer to
ment, Attaching to Body”, page 303
.
5 - Roof Reinforcement
❑ Only with a sunroof
❑ Install on the body. Refer to
⇒ “7.4 Roof Reinforcement, Attaching to Body”, page 303
6 - Clip
❑ Quantity: 9
❑ Remove the clips that are still in the mounting points on the body using the Omega Clip Tool - T40280-
❑ Replace damaged or deformed retaining clips
7 - Roof End Strip
❑ Removing and installing. Refer to
⇒ “7.2 Roof End Strip, Removing and Installing”, page 299
.
8 - Clip
❑ Only with a sunroof
❑ Quantity: 23
❑ Insert in the headliner
❑ Remove any remaining clips in the frame
❑ Replace damaged or deformed retaining clips
7.2
Roof End Strip, Removing and Installing
Special tools and workshop equipment required
♦ Wedge Set - T10383-
Removing
– Loosen the roof end strip -1- near the clips from the body
mounts using the Wedge Set - T10383- .
– Remove the roof end strip -1- downward.
Installing
Note
♦
Check all the fasteners for damage and replace if necessary.
♦
Remove any remaining clips in the body mounting points using
the Omega Clip Tool - T40280- . To install, insert into the roof
end strip.
♦
Make sure the roof end strip is inside the rear lid seal molding
after it is installed.
Install in reverse order of removal.
7.3
Headliner, Removing and Installing
⇒ “7.3.1 Headliner, Removing and Installing, Sedan”, page 299
⇒ “7.3.2 Headliner, Removing and Installing, Wagon”,
7.3.1
Headliner, Removing and Installing, Se‐
dan
Special tools and workshop equipment required
♦ Wedge Set - T10383-
♦ Release Pliers - VAS6427-
Removing
Vehicles with Sunroof
– Open the sunroof -1- all the way.
– Open the sun shade -2- about
2
/3.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст