Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 857
7.2
Overview - Trailing Arm
1 - Cover
2 - Bolt
❑ 50 Nm + 45°
❑ Replace after removal
3 - Mounting Bracket
4 - Bolt
❑ 90 Nm + 90°
❑ Replace after removal
5 - Rivet
❑ Replace after removal
6 - Bracket
❑ For the rear brake cable
7 - Bolt
❑ 70 Nm +90°
❑ Replace after removal
❑ M14 x 1.5
8 - Bolt
❑ 70 Nm + 90°
❑ Replace after removal
❑ M12 x 1.5
9 - Wheel Bearing Housing
❑ There are different ver‐
sions. Refer to the Parts
Catalog.
10 - Trailing Arm
❑ Removing and instal‐
ling. Refer to
moving and Installing”, page 234
11 - Bonded Rubber Bushing
❑ Note the installation position
❑ Replacing. Refer to
⇒ “7.7 Trailing Arm, Servicing”, page 237
7.3
Wheel Bearing Housing, Removing and
Installing
⇒ “7.3.1 Wheel Bearing Housing, Removing and Installing, Multi-
Link Suspension, FWD”, page 213
⇒ “7.3.2 Wheel Bearing Housing, Removing and Installing, Multi-
Link Suspension, AWD”, page 217
7.3.1
Wheel Bearing Housing, Removing and
Installing, Multi-Link Suspension, FWD
Special tools and workshop equipment required
♦ Torque Wrench 1332 40-200Nm - VAG1332-
♦ Engine and Gearbox Jack - VAS6931-
Removing
– Loosen the wheel bolts.
– Raise the vehicle.
– Remove the wheel.
– Remove the wheel bearing unit. Refer to
⇒ “7.4 Wheel Bearing Unit, Removing and Installing”,
– Remove the heat shield. Refer to ⇒ Brake System; Rep. Gr.
46 ; Overview - Rear Brakes .
Vehicles with Level Control System Sensor
– Remove the spring. Refer to
⇒ “6.4 Spring, Removing and Installing”, page 202
– Remove the bolts -1-.
– Remove the Left Rear Level Control System Sensor -2- brack‐
et.
Vehicles with Stone Chip Protection
– Remove the expanding rivets -1-.
– Remove the bolts -2- for the stone chip protection -3-.
Continuation for all Vehicles
– Disconnect the connector from the ABS speed sensor.
– Secure both sides of the vehicle on the hoist arms using -
T10038- .
1 - -T10038-
WARNING
The vehicle could slide off the hoist if it is not secured.
– Place the -VAS6931- -1- under the tie rod and push lightly up‐
ward.
– Remove the bolts -2 and 3- one after the other.
– Remove the -VAS6931- -1- from under the tie rod.
– Unscrew the nut -1- and remove the washer -2-.
– Remove the bolt -3-.
– Remove the bolt -1-.
– Remove the wheel bearing housing -2-.
Installing
Install in reverse order of removal while noting the following:
Complete the following steps in the exact order specified.
– Insert the wheel bearing housing -2-.
– Insert the bolt -1- and tighten hand-tight.
– Insert the bolt -3-.
– Slide on the washer -2-.
– Tighten the nut -1- hand-tight.
– Place the -VAS6931- -1- under the tie rod and push lightly up‐
ward.
– Install the bolts -2- and -3- by hand.
– Remove the -VAS6931- -1- from under the tie rod.
– Install the heat shield. Refer to ⇒ Brake System; Rep. Gr. 46 ;
Overview - Rear Brakes .
– Install the wheel bearing unit. Refer to
⇒ “7.4 Wheel Bearing Unit, Removing and Installing”,
Only fasten the threaded connections on the wheel bearing hous‐
ing in the curb weight position.
– Tighten the bolt -1-.
– Tighten the nut -1-.
– Remove the -VAS6931- with the -T10149- from the wheel hub.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст