Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 323
4.1.3
Overview - Impact Guard
Note
Depending on the engine version, slight deviations must be considered when removing and installing.
1 - Impact Guard
❑ Removing
– Remove the bolts
-2, 3, and 4-.
– Remove the noise insu‐
lation toward the rear
from the lock carrier.
2 - Bolt
❑ 20 Nm
❑ Quantity: 2 on each side
3 - Bolt
❑ 2 Nm
❑ Quantity: 3 on the left
side
❑ Quantity: 4 on the right
side
4 - Bolt
❑ 20 Nm
❑ Replace after removing
❑ Microencapsulated
❑ Quantity: 3
5 - Impact Guard Bracket
❑ Left and right
6 - Bolt
❑ 20 Nm
❑ Quantity: 1 on each side
5
Underbody Panel
⇒ “5.1 Overview - Underbody Panels”, page 425
⇒ “5.2 Underbody Panels, Removing and Installing”, page 426
⇒ “5.3 Center Underbody Panels, Removing and Installing”, page
427
⇒ “5.4 Rear Underbody Panel, Removing and Installing”,
page 429
⇒ “5.5 Front Tunnel Brace, Removing and Installing”, page 430
⇒ “5.6 Rear Tunnel Brace, Removing and Installing”, page 431
5.1
Overview - Underbody Panels
1 - Front Cover
❑ Left and right
❑ Removing and instal‐
ling. Refer to
.
2 - Underbody Trim Panels
❑ Left and right
❑ Removing and instal‐
ling. Refer to
.
3 - Nut
❑ 2 Nm
❑ With retainer
❑ Quantity: 7 on each side
4 - Rear Underbody Trim Panel
❑ Removing and instal‐
ling. Refer to
5 - Spring Nut
6 - Bolt
❑ 2 Nm
7 - Expanding Rivet
8 - Lock Washer
9 - Rear Tunnel Brace
❑ Removing and instal‐
ling. Refer to
⇒ “5.6 Rear Tunnel Brace, Removing and Installing”, page 431
10 - Nut
❑ 20 Nm
❑ Quantity: 2 on each side
11 - Center Underbody Trim Panel
❑ Removing and installing. Refer to
⇒ “5.3 Center Underbody Panels, Removing and Installing”, page 427
12 - Expanding Rivet
❑ Quantity: 4
13 - Front Tunnel Brace
❑ Removing and installing. Refer to
⇒ “5.5 Front Tunnel Brace, Removing and Installing”, page 430
.
14 - Bolt
❑ 20 Nm
❑ Quantity: 2 on each side
5.2
Underbody Panels, Removing and In‐
stalling
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Note
Depending on the engine version, slight deviations must be considered when removing and installing.
Removing
– Remove the center underbody panels. Refer to
⇒ “5.3 Center Underbody Panels, Removing and Installing”,
.
– Release the mounting tab and remove the front cover
-2 or 5- from the retainer in the direction of travel toward the
rear.
– Remove the nuts -3-.
– Remove the underbody panel -1 or 4-.
Installing
Install in reverse order of removal.
Tightening Specifications
5.3
Center Underbody Panels, Removing
and Installing
⇒ “5.3.1 Center Underbody Trim Panels, Removing and Installing,
Underbody Trim Panels”, page 427
⇒ “5.3.2 Center Underbody Trim Panels, Removing and Installing,
5.3.1
Center Underbody Trim Panels, Removing and Installing, Underbody Trim
Panels
Note
Depending on the engine version, slight deviations must be considered when removing and installing.
Removing
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст