Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 388
– Drill out the attachment points -2- for the trim molding -1- from
the door trim panel using an appropriate drill until the trim
molding starts to loosen from the door trim panel.
Caution
The door trim panel must not be damaged by drilling.
– Carefully loosen the attachment points -2- one after the other
and remove the trim molding -1- from the door trim panel.
Installing
Lock washers near the trim strip (4-door): 17 mm × 7.5 mm, quan‐
tity: 6. Allocation. Refer to the Parts Catalog.
Lock washers near the trim strip (2-door): 17 mm × 7.5 mm, quan‐
tity: 9. Allocation. Refer to the Parts Catalog.
Lock washers near the interior door mechanism: 13.4 mm × 6 mm,
quantity: 8. Allocation. Refer to the Parts Catalog.
– Insert the new trim molding -1- into the door trim panel.
– Press the lock washers -2- all the way onto the pins -3- of the
trim molding.
– Press the remaining lock washers near the interior door mech‐
anism onto the trim molding pins as described.
– Cut back the trim molding pins -3- above the lock washers
-2- so that the projecting end is a maximum of 2 mm.
– Install the Exterior Rearview Mirror Adjuster - EX11- with the
Driver Interior Locking Button - E308- . Refer to ⇒ Electrical
Equipment; Rep. Gr. 96 ; Component Location Overview -
Controls in Front Doors .
– Install the front door trim panel. Refer to
⇒ “1.2 Front Door Trim Panel, Removing and Installing”, page
2
Rear Door Trim Panels
⇒ “2.1 Overview - Rear Door Trim Panel”, page 202
⇒ “2.2 Rear Door Trim Panel, Removing and Installing”,
page 203
⇒ “2.3 Interior Door Mechanism, Removing and Installing”,
page 206
⇒ “2.4 Trim Molding, Removing and Installing”, page 207
2.1
Overview - Rear Door Trim Panel
Note
The overview illustration shows the driver side rear door trim panel The illustration for the front passenger side
is identical.
1 - Door Trim Panel
❑ Removing and instal‐
ling. Refer to
.
2 - Driver Side Rear Power
Window Button - E711-
❑ Only on vehicles with a
power window regulator
❑ Component Location
Overview. Refer to ⇒
Electrical Equipment;
Rep. Gr. 96 ; Controls;
Component Location
Overview - Controls in
Rear Doors .
3 - Screw
❑ 4.5 Nm
❑ Quantity: 2
4 - Window Crank
❑ Only on vehicles with a
manual window regula‐
tor
❑ Removing and instal‐
ling. Refer to ⇒ Body
Exterior; Rep. Gr. 58 ;
Door Components; Win‐
dow Crank, Removing
and Installing .
5 - Grip Recess Upper Section
6 - Rear Reflector
❑ Component Location
Overview. Refer to ⇒
Electrical Equipment;
Rep. Gr. 96 ; Lamps; Component Location Overview - Rear Door Lamps .
7 - Clip
❑ Quantity: 6
❑ Insert in the trim panel
❑ Replace damaged or deformed clips
2.2
Rear Door Trim Panel, Removing and
Installing
Note
The removal and installation for the driver side rear door trim
panel is described. The removal and installation for the front pas‐
senger side is identical.
Special tools and workshop equipment required
♦ Trim Removal Wedge - 3409-
♦ Wedge Set - T10383-
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Removing
Vehicles without Power Window Regulator
– Remove the window crank. Refer to ⇒ Body Exterior; Rep.
Gr. 58 ; Door Components; Window Crank, Removing and
Installing .
Continuation for All Vehicles
– Turn off the ignition and all electrical equipment and remove
the ignition key.
– Remove the handle molding upper section -1- with the Trim
Removal Wedge - 3409- from the mounts in the door trim pan‐
el.
– Remove the bolts -1-.
– Remove the rear reflector. Refer to ⇒ Electrical Equipment;
Rep. Gr. 96 ; Lamps; Component Location Overview - Rear
Door Lamps for the component location overview.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст