Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 823
• The wheel bearing -1- must face up in order to remove the
wheel bearing unit.
• Always set the wheel bearing unit down on the wheel hub
-2-.
• Never reach inside when lifting the wheel bearing.
• Hold the wheel bearing only on the outside.
Installing
Install in reverse order of removal. Note the following:
– Tighten nuts -arrows-.
Note
♦
Tighten the nuts -arrows- in curb weight position. Refer to
⇒ “3.8.1 Wheel Bearing in Curb Weight, Lifting Vehicles with
Coil Spring, Front Axle”, page 6
.
♦
The level control system sensor lever must point toward vehi‐
cle exterior.
♦
The thread on the vehicle level sensor must be installed into
the exterior hole in the control arm. The tab on the vehicle level
sensor bracket must lock into the inner hole in order to assure
a correct installation position.
– For vehicles with a level control system sensor, perform the
basic setting for the wheel damping electronics using the Ve‐
hicle Diagnostic Tester.
Tightening Specifications
♦ Refer to
⇒ “5.1 Overview - Wheel Bearing”, page 70
♦ Refer to
⇒ “6.2 Overview - Drive Axle”, page 80
♦ Refer to
⇒ “2.1 Overview - Subframe”, page 16
♦ Refer to
⇒ “4.1 Overview - Lower Control Arm and Ball Joint”,
♦ Refer to
⇒ “2.1 Overview - Front Level Control System Sensor”,
♦ Brake rotor bolt. Refer to ⇒ Brake System; Rep. Gr. 46 ;
Overview - Front Brakes .
6
Drive Axle
⇒ “6.1 Overview - Drive Axle”, page 79
⇒ “6.2 Overview - Drive Axle”, page 80
⇒ “6.3 Drive Axle, Removing and Installing”, page 85
⇒ “6.4 Drive Axle Threaded Connection, Loosening and Tighten‐
ing”, page 101
⇒ “6.5 Drive Axle Heat Shield, Removing and Installing”,
page 102
⇒ “6.6 Drive Axle, Disassembling and Assembling”, page 103
⇒ “6.7 Outer CV Joint, Checking”, page 113
⇒ “6.8 Inner CV Joint, Checking”, page 114
6.1
Overview - Drive Axle
I -
⇒ “6.2.1 Overview - Drive Axle,
II -
⇒ “6.2.2 Overview - Drive Axle,
III -
⇒ “6.2.3 Overview - Drive Axle,
Triple Roller Joint AAR3300i”,
Difference of Drive Axles in Installed Condition
VL100
VL107
AAR3300i At‐
tached
AAR3300i Bol‐
ted
Diameter of inner joint in mm
100
107
-
-
VL100
VL107
AAR3300i At‐
tached
AAR3300i Bol‐
ted
Cover between inner joint and
flange shaft
-
X
-
-
Inner joint inserted into transmis‐
sion
(automatic transmission only)
-
-
X
-
6.2
Overview - Drive Axle
⇒ “6.2.1 Overview - Drive Axle, CV Joint VL 100”, page 80
⇒ “6.2.2 Overview - Drive Axle, CV Joint VL 107”, page 82
⇒ “6.2.3 Overview - Drive Axle, Triple Roller Joint AAR3300i”,
6.2.1
Overview - Drive Axle, CV Joint VL 100
1 - Outer CV Joint
❑ Replace only as com‐
plete unit.
❑ Removing. Refer to
❑ Installing: Using a plas‐
tic hammer, drive onto
the shaft as far as the
stop
❑ Checking. Refer to
2 - Bolt
❑ 200 Nm +180°
❑ Replace after removal
❑ Loosening and tighten‐
ing. Refer to
3 - Right Drive Axle
4 - Clamp
❑ Replace after removal
❑ Tensioning. Refer to
5 - CV Boot
❑ Check for tears and
scuffing
❑ Material: polyelastomer
6 - Clamp
❑ Replace after removal
❑ Tensioning. Refer to
⇒ Fig. ““Tightening Clamping Sleeve on Outer Joint”“ , page 106
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст