Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 241
1 - Front Door
❑ Removing and instal‐
ling. Refer to
❑ Adjusting. Refer to
2 - Sticker
❑ 28 mm diameter
❑ Use commercially avail‐
able duct tape if needed
3 - Sticker
❑ 32 mm diameter
❑ Use commercially avail‐
able duct tape if needed
4 - Insulation
❑ Self-adhesive
❑ Installing:
– Cut to size if necessary,
200 mm x 100 mm. Po‐
sition as shown in the il‐
lustration.
– Warm using the Wiring
Harness Repair Set -
Hot Air Blower -
VAS1978/14A- and
then press firmly onto
the outer door panel.
5 - Door Inner Cover
❑ Removing and instal‐
ling. Refer to
⇒ “2.6 Door Inner Cover, Removing and Installing”, page 104
6 - Outer Door Seal
❑ For 4-door
❑ Removing and installing. Refer to
⇒ “1.3 Outer Door Seal, Removing and Installing”, page 84
7 - Outer Door Seal
❑ For 2-door
❑ Removing and installing. Refer to
⇒ “1.3 Outer Door Seal, Removing and Installing”, page 84
8 - Inner Outer Cover
❑ Removing and installing. Refer to
⇒ “2.17 Outer Cover, Removing and Installing”, page 130
9 - Outer External Cushion
❑ Removing and installing. Refer to
⇒ “2.17 Outer Cover, Removing and Installing”, page 130
10 - Insulation
❑ Self-adhesive
❑ Installing:
– Cut to size if necessary, 250 mm x 160 mm. Position as shown in the illustration.
– Warm using the Wiring Harness Repair Set - Hot Air Blower - VAS1978/14A- and then press firmly onto
the outer door panel.
11 - Sticker
❑ 19 mm diameter
❑ Use commercially available duct tape if needed
12 - Inner Window Shaft Strip
❑ Removing and installing. Refer to
⇒ “2.16 Inner Window Shaft Strip, Removing and Installing”, page 129
.
13 - Outer Window Shaft Strip
❑ Removing and installing. Refer to
⇒ “2.15 Outer Window Shaft Strip, Removing and Installing”, page 126
14 - Window Guide
❑ Removing and installing. Refer to
⇒ “2.14 Window Guide, Removing and Installing”, page 124
.
15 - Sticker
❑ Quantity: 3 for 4-door
❑ Quantity: 4 for 2-door
❑ 15 mm x 50 mm
❑ Use commercially available duct tape if needed
2.2
Overview - Window Regulator
1 - Front Door
2 - Nut
❑ 6 Nm
❑ Quantity: 5
3 - Window Regulator
❑ Removing and instal‐
ling. Refer to
.
4 - Screw
❑ 3 Nm
❑ Quantity: 3
5 - Driver Window Regulator
Motor - V147- / Front Passen‐
ger Window Regulator Motor -
V148-
❑ Removing and instal‐
ling. Refer to
.
6 - Clip
2.3
Overview - Door Handle and Door Lock
Note
The illustration shows the left side. The right side is identical.
1 - Door Lock
❑ Removing and instal‐
ling. Refer to
2 - Screw
❑ 3.5 Nm
3 - Bracket
❑ Removing and instal‐
ling. Refer to
4 - Lock Cylinder
❑ Removing and instal‐
ling. Refer to
❑ Is only installed on the
driver door.
5 - Backing Plate
6 - Cap
❑ For the lock cylinder, re‐
moving and installing.
Refer to
❑ Without the lock cylin‐
der, removing and in‐
stalling. Refer to
.
7 - Door Handle
❑ Removing and installing. Refer to
⇒ “2.11 Door Handle, Removing and Installing”, page 114
.
8 - Screw
❑ 1.5 Nm
❑ Loosening this bolt loosens the bracket from the door.
9 - Release Cable
❑ From the door lock -1- to the bracket -3-
10 - Release Cable
❑ From the interior door mechanism to the door lock -1-
❑ With a grommet for the pass through on the cover
11 - Bolt
❑ 18 Nm
❑ Quantity: 2
12 - Cap
2.4
Window Regulator Motor, Removing
and Installing
Special tools and workshop equipment required
♦ Torque Wrench 1783 - 2-10Nm - VAG1783-
Note
♦
The following describes the removal and installation of the left window regulator motor. Removing and in‐
stalling the right window regulator motor is identical.
♦
The Driver Door Control Module - J386- / Front Passenger Door Control Module - J387- -4- is separated
from the Driver Window Regulator Motor - V147- / Front Passenger Window Regulator Motor - V148- -1-.
♦
The Driver Door Control Module - J386- / Front Passenger Door Control Module - J387- is clipped in the
door. Refer to
⇒ “3.2 Driver Door Control Module J386 and Front Passenger Door Control Module J387 , Removing and
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст