Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 461
– Install the bracket -2-. Refer to ⇒ Body Interior; Rep. Gr. 68 ;
Center Console; Center Console, Removing and Installing .
– Install the air guide channel from the center console. Refer to
⇒ Heating, Ventilation and Air Conditioning; Rep. Gr. 87 ; Air
Routing; Overview - Air Routing and Air Distribution in Pas‐
senger Compartment .
– Install the center console. Refer to ⇒ Body Interior; Rep. Gr.
68 ; Center Console; Center Console, Removing and Instal‐
ling .
– Install the selector lever handle. Refer to
⇒ “2.3 Selector Lever Handle, Removing and Installing”, page
– Adjust the selector lever cable. Refer to
⇒ “2.8 Selector Lever Cable, Checking and Adjusting”,
.
– Check the selector mechanism. Refer to
⇒ “2.7 Gearshift Mechanism, Checking”, page 67
.
Tightening Specifications
♦ Selector mechanism to the body. Refer to
⇒ “2.1 Overview - Selector Mechanism”, page 47
.
2.5.3
Shift Lever Mechanism without Selector
Lever Cable, Removing and Installing,
ECS
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
Mandatory Replacement Parts
♦ Lock Washer - Selector Housing
♦ Cover - Selector Housing
Short Description
Remove the center console inside the passenger compartment.
It is necessary to remove the heat shield under the vehicle.
Removing
– Remove the selector lever handle. Refer to
⇒ “2.3 Selector Lever Handle, Removing and Installing”, page
– Remove the center console. Refer to ⇒ Body Interior; Rep.
Gr. 68 ; Center Console; Center Console, Removing and In‐
stalling .
– Remove the air guide channel from the center console. Refer
to ⇒ Heating, Ventilation and Air Conditioning; Rep. Gr. 87 ;
Air Routing; Overview - Air Routing and Air Distribution in Pas‐
senger Compartment .
– Remove the bracket -2-, to do this remove the left and right
bolts -1-.
– Disconnect the connector from the selector mechanism to the
vehicle wiring harness.
– Position the selector lever on the selector mechanism in the
“N” position.
– Remove the center tunnel heat shield under the gearshift
mechanism. Refer to ⇒ Body Exterior; Rep. Gr. 66 ; Molding/
Trim/Extensions/Trim Panels; Floor Heat Shield, Removing
and Installing .
– Pry up the lower cover from the selector mechanism in the
direction of -arrow- and remove.
Note
Do not reuse the cover. Always replace after removing.
– Release the cable as shown with a screwdriver and remove
from the selector lever in the direction of -arrows-.
– Remove the lock washer in the direction of -arrow-.
Always replace the lock washer.
– Remove the cable from the selector mechanism.
– Remove the bracket -A-, if equipped.
– Remove the nuts -arrows- in the vehicle interior.
– Remove the selector mechanism -B- with the gearshift hous‐
ing downward.
Installing
Install in reverse order of removal. Note the following:
Note
♦
Do not bend or kink the selector lever cable.
♦
Do not lubricate the selector lever cable.
♦
After installation, the selector lever cable movement must be
checked and adjusted.
• The selector mechanism selector lever is in the “N” position.
– Guide the cable on the selector mechanism, inset in the se‐
lector lever and install new lock washer.
– Install the heat shield under the gearshift mechanism. Refer
to ⇒ Body Exterior; Rep. Gr. 66 ; Molding/Trim/Extensions/
Trim Panels; Floor Heat Shield, Removing and Installing .
– Install the bracket -2-. Refer to ⇒ Body Interior; Rep. Gr. 68 ;
Center Console; Center Console, Removing and Installing .
– Install the air guide channel from the center console. Refer to
⇒ Heating, Ventilation and Air Conditioning; Rep. Gr. 87 ; Air
Routing; Overview - Air Routing and Air Distribution in Pas‐
senger Compartment .
– Install the center console. Refer to ⇒ Body Interior; Rep. Gr.
68 ; Center Console; Center Console, Removing and Instal‐
ling .
– Install the selector lever handle. Refer to
⇒ “2.3 Selector Lever Handle, Removing and Installing”, page
– Adjust the selector lever cable. Refer to
⇒ “2.8 Selector Lever Cable, Checking and Adjusting”,
.
– Check the selector mechanism. Refer to
⇒ “2.7 Gearshift Mechanism, Checking”, page 67
.
Tightening Specifications
♦ Selector mechanism to the body. Refer to
⇒ “2.1 Overview - Selector Mechanism”, page 47
.
2.6
Selector Lever Cable, Removing and In‐
stalling
⇒ “2.6.1 Selector Lever Cable, Removing and Installing, ZF”,
⇒ “2.6.2 Selector Lever Cable, Removing and Installing, ECS”,
2.6.1
Selector Lever Cable, Removing and In‐
stalling, ZF
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
Mandatory Replacement Parts
♦ Lock Washers - Selector Lever Cable
Removing
– Remove the air filter housing. Refer to ⇒ Engine Mechanical,
Fuel Injection and Ignition; Rep. Gr. 24 ; Air Filter; Air Filter
Housing, Removing and Installing or ⇒ Rep. Gr. 23 ; Air Filter;
Air Filter Housing, Removing and Installing
Loosen the adjusting screw -arrow-.
– Remove the lock washers -A and B-. The lock washers must
later be replaced when adjusting selector lever cable.
Use pliers to remove the lock washer -B-. Do not use a sharp-
edged lever. Otherwise the selector lever cable could get dam‐
aged.
– Position the selector lever on the selector mechanism in the
“N” position. The cable can only be loosened in this position.
– Remove the center tunnel heat shield under the gearshift
mechanism. Refer to ⇒ Body Exterior; Rep. Gr. 66 ; Molding/
Trim/Extensions/Trim Panels; Floor Heat Shield, Removing
and Installing .
– Remove the plugs, and remove the lock washer -arrow-.
Always replace the lock washer.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст