Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 439
5 - Backrest Frame
6 - Backrest Cushion
❑ Allocation. Refer to the Parts Catalog.
❑ Backrest cover and cushion, removing and installing. Refer to
⇒ “1.5 Backrest Cover and Cushion, Removing and Installing”, page 406
.
❑ Backrest cover and backrest cushion, separating. Refer to
⇒ “1.7 Backrest Cover and Cushion, Separating”, page 410
1.3
Overview - Seat Heating Element
1 - Seat Cushion
❑ Allocation. Refer to the
Parts Catalog.
2 - Heating Element
❑ Driver seat Driver Seat
Heating Element - Z6-
❑ Passenger seat Front
Passenger Seat Heat‐
ing Element - Z8-
❑ On vehicles with a pas‐
senger occupant detec‐
tion system, the Front
Passenger Seat Heat‐
ing Element - Z8- and
the passenger occupant
detection system pres‐
sure sensor are a
shared component.
❑ On vehicles with a pas‐
senger occupant detec‐
tion system, the seat
heating element must
not be separated from
the front seat cushion
cover.
❑ If the seat heating ele‐
ment is separated from
the front seat cushion
cover on vehicles with a
passenger occupant de‐
tection system, then
both components must
be replaced.
❑ Allocation. Refer to the
Parts Catalog.
❑ Replace after removing.
Refer to
⇒ “1.8 Driver/Front Passenger Seat Heating Element Z6 / Z8 , Removing and Installing”, page 414
.
3 - Backrest Cushion
❑ Allocation. Refer to the Parts Catalog.
4 - Heating Element
❑ Driver seat Driver Backrest Heating Element - Z7-
❑ Passenger seat Front Passenger Backrest Heating Element - Z9-
❑ Allocation. Refer to the Parts Catalog.
❑ Replace after removing. Refer to
⇒ “1.9 Driver/Front Passenger Backrest Heating Element Z7 / Z9 , Removing and Installing”,
5 - Wire
6 - Wire
1.4
Seat Pan Cover and Cushion, Remov‐
ing and Installing
Special tools and workshop equipment required
♦ Backrest Panel Tool - 3370-
Note
The following describes removing and installing components on
the left seat. Removing and installing components on the right
seat is identical.
Removing
– Remove the front seat. Refer to
⇒ “2.10 Front Seat, Removing and Installing”, page 335
.
– Secure the seat on the Fixture for Seat Repair . Refer to
⇒ “1.2 Front Seat, Mounting on Fixture for Seat Repair”, page
– Remove the tunnel side seat trim. Refer to
⇒ “2.13 Tunnel-Side Seat Trim, Removing and Installing”,
.
– Remove the sill-side seat trim. Refer to
⇒ “2.14 Sill-Side Seat Trim, Removing and Installing”,
.
– Remove the sill-side seat trim bracket. Refer to
⇒ “2.15 Seat Trim Bracket, Removing and Installing”,
.
– Remove the backrest. Refer to
⇒ “2.16 Front Backrest, Removing and Installing”, page 349
– Remove the storage compartment, if equipped. Refer to
⇒ “2.35 Storage Compartment, Removing and Installing”,
.
– Release and remove the connector.
– Free up the wiring harnesses.
– Disengage the clamping strips -1 and 2- using the Backrest
Panel Tool - 3370- .
– Remove the cover with the cushion from the seat pan.
– Separate the cover from the cushion. Refer to
⇒ “1.6 Seat Pan Cover and Cushion, Separating”,
.
Installing
Install in reverse order of removal.
Tightening Specifications
♦ Refer to
1.5
Backrest Cover and Cushion, Removing
and Installing
Note
The following describes removing and installing components on
the left seat. Removing and installing components on the right
seat is identical.
Special tools and workshop equipment required
♦ Trim Removal Wedge - 3409-
♦ Upholstery Clip Pliers - VAG1634-
♦ Backrest Panel Tool - 3370-
Removing
WARNING
Follow the General Safety Precautions when working with air‐
bags, belt tensioners and battery cut-out units (pyrotechnic
components).
Refer
to
⇒ “1.2 Safety Precautions for Pyrotechnic Components”, page
.
– Remove the front seat. Refer to
⇒ “2.10 Front Seat, Removing and Installing”, page 335
– Secure the seat on the Fixture for Seat Repair . Refer to
⇒ “1.2 Front Seat, Mounting on Fixture for Seat Repair”, page
.
Only for Vehicles without Entry Assistance
– Remove the backrest. Refer to
⇒ “2.16 Front Backrest, Removing and Installing”, page 349
.
Continuation for All Vehicles
– Remove the headrest. Refer to
⇒ “2.23 Headrest, Removing and Installing”, page 360
.
– Unclip the headrest locking mechanism caps using the Trim
Removal Wedge - 3409- .
– If equipped, remove the lumbar support adjusting lever. Refer
to
– Open the clamping strip -4- using the Backrest Panel Tool -
3370- .
– Roll the front and rear backrest cover -1- upward.
– Pull up the backrest cover -1- in order to reach the right and
left upholstery clips -5-.
– Open the upholstery clips -5- using pliers -6-.
– Pull the backrest cover -1- on the cushion -7- upward.
– Continue pulling the backrest cover -1- up in order to reach the
next upholstery clips -5-.
– Loosen the clip -3- from both sides of the back of the backrest
frame -2-.
– To do so, use the Trim Removal Wedge - 3409- .
– Open the upholstery clips -5- on the backside.
– Continue pulling the backrest cover -1- up in order to reach the
next upholstery clips -5-.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст