Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 623
• The arrow -2- on the Engine Support Bridge - Engine Support
29 - 10-222A/29- always points in the direction of travel.
• The Engine Support Bridge - Engine Support 29 - 10-222A/29-
on the load-bearing components of the fender bolting edge.
Assemble the Engine Support Bridge - 10-222A- as follows:
– Slide the Engine Support Bridge - Engine Support 18 -
10-222A/18- and two Engine Support - Basic Set Movable
Joint - T40091/3- onto the Engine Support Bridge - 10-222A- .
– Install the Square Pipe - T40091/1- in the Engine Support -
Basic Set - Movable Joint - T40091/3- .
– Push the Engine Support Bridge - Spindle - 10 - 222 A /11- on
the square pipe -T40091/1-
– Place the Engine Support Bridge - Spindle - 10 - 222 A /11-
on the Engine Support Bridge - Engine Support 18 - 10-222A/
18- .
– Tighten the Engine Support Bridge - 10-222A- on the Engine
Support Bridge - Engine Support 29 - 10-222A/29- .
– Install the Engine/Gearbox Support Shackle (2 pc.) - 10-222A/
12- as shown on the engine.
– Install the Engine Support Brackets - T40093/3-6- -A- as fol‐
lows. (⇒ next illustration).
The adapter -A- is the Engine Support Brackets - T40093/3-6- and
is positioned as follows:
– If present, remove wires from the front area of both longitudinal
members -arrow-. Do not disconnect line system.
– Place the Engine Support Brackets - T40093/3-6- on both lon‐
gitudinal members (the right longitudinal member is illustrated
here).
– If necessary, carefully unclip the A/C system pipe in the front
area. Do not disconnect the line system. Refer to ⇒ Heating,
Ventilation and Air Conditioning; Rep. Gr. 87 ; Refrigerant
Circuit; System Overview - Refrigerant Circuit .
• The Engine Support Brackets - T40093/3-6- locks respectively
with the pins -A- behind the tab on the longitudinal member
-arrow-.
– Install the Engine Support - Supplement Kit Spindle -
T40093/3- .
– Connect the Engine Support - Supplement Kit Spindle -
T40093/3- over the Engine Support - Basic Set Square Pipe -
T40091/1- with the Engine Support Bridge - 10-222A- and
tension it (⇒ previous illustration).
Note
♦
The Engine Support - Basic Set - Square Pipe - T40091/1-
must not touch the windshield.
♦
The Engine Support Bridge - Engine Support 18 - 10-222A/18-
must not lie on the windshield wiper arm.
– Engage the Spindles into the engine lifting eyes using the En‐
gine/Gearbox Support Shackle (2 pc.) - 10-222A/12- .
– Pretension the engine/transmission assembly and Engine
Support Bridge via the Spindles .
– Raise the vehicle and remove the front wheels.
– Remove the noise insulation. Refer to ⇒ Body Exterior; Rep.
Gr. 66 ; Noise Insulation; Overview - Noise Insulation .
– Remove the lower section of the left front wheel housing liner.
Refer to ⇒ Body Exterior; Rep. Gr. 66 ; Wheel Housing Liner;
Front Wheel Housing Liner, Removing and Installing .
– Remove the left and right driveshafts. Refer to ⇒ Suspension,
Wheels, Steering; Rep. Gr. 40 ; Drive Axle; Drive Axle, Re‐
moving and Installing .
– Disconnect the connectors -1- and -2- from the front of the
transmission.
– Open the coolant hose bracket -2- and remove the coolant
hose -3-.
– Unclip the wiring harness -arrow-.
– Remove the bolts -4- from the engine and remove the bracket
-1-.
– Remove the three converter nuts -arrow- through the opening
in the intermediate plate using the Storage Compartment Cen‐
tral Locking Motor - V/175- .
– To do this, turn the engine 120° further in the direction of en‐
gine rotation at the belt pulley/vibration damper.
Note
The torque converter will be pulled out when the transmission is
separated from the engine if all three nuts are not removed!
– Remove bolts -1 through 3- and remove pendulum support.
– Remove the bracket bolts -arrows- for the exhaust system on
the subframe.
– Remove the bolts -2- that attach the transmission mount to the
transmission bracket -A- and the bolts -1- that attach the trans‐
mission bracket to the transmission.
– Remove the transmission bracket -A-. Lower the engine with
the transmission slightly using the spindles on the Engine
Support Bridge .
Four turns should be sufficient.
– Remove the lower bolts -5 to 7- between the engine and the
transmission.
Note
The rear bolts -8- and -9- that connect the engine to the trans‐
mission remain installed.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст