Volkswagen Golf / Golf GTI / Golf Variant. Manual — part 571
1.2
Overview - Gearshift Knob and Cover
1 - Gearshift Housing with
Gearshift Lever
2 - Nut
❑ M6: 8 Nm
❑ M8: 25 Nm
3 - Bracket
❑ For the center console
❑ Overview. Refer to ⇒
Body Interior; Rep. Gr.
68 ; Center Console;
Overview - Center Con‐
sole .
4 - Bracket
❑ For the center console
❑ Overview. Refer to ⇒
Body Interior; Rep. Gr.
68 ; Center Console;
Overview - Center Con‐
sole .
5 - Noise Insulation
6 - Badge
❑ Can be carefully pried
off the plastic or leather
gearshift knob using
Trim Removal Wedge -
3409- .
7 - Gearshift Knob
❑ With boot
❑ The shift knob and boot
cannot be separated
from each other.
❑ Always replace together
❑ Removing and instal‐
ling. Refer to
⇒ “1.4 Gearshift Knob, Removing and Installing”, page 54
.
8 - Center Console
❑ Overview. Refer to ⇒ Body Interior; Rep. Gr. 68 ; Center Console; Overview - Center Console .
9 - Clamp
❑ For securing the shift knob to the shift lever
❑ Replace after removing
❑ Secure on the gearshift knob using Hose Clamp Pliers - VAG1275- .
1.3
Overview - Selector Mechanism
Note
♦
Lubricate the bearing areas and the sliding surfaces.
♦
Grease allocation. Refer to the Parts Catalog.
1 - Gearshift Shaft with Gear‐
shift Cover
2 - Sliding Shoe
3 - Relay Lever
❑ Allocation. Refer to the
Parts Catalog.
❑ Installed position. Refer
to
❑ Adjust the gearshift
mechanism after instal‐
ling. Refer to
.
❑ Relay lever and cable
retainer, removing and
installing. Refer to
4 - Cable Retainer
❑ For attaching the selec‐
tor cable to the relay lev‐
er
❑ Adjust the gearshift
mechanism after instal‐
ling. Refer to
.
❑ Do not interchange, ca‐
ble locking mechanisms
for selector cable on
linkage lever and for shift cable on transmission shift lever are different
❑ Allocation. Refer to
⇒ Fig. ““Cable Retainer Allocation”“ , page 60
❑ Remove from the relay lever. Refer to
❑ Press onto the relay lever. Refer to
⇒ Fig. ““Installing the Selector Cable Retainer on the Relay Lever”“ , page 59
5 - Cable Retainer
❑ For attaching the shift cable to the transmission shift lever
❑ Adjust the gearshift mechanism after installing. Refer to
⇒ “1.6 Selector Mechanism, Adjusting”, page 63
.
❑ Do not interchange, cable locking mechanisms for selector cable on linkage lever and for shift cable on
transmission shift lever are different
❑ Allocation. Refer to
6 - Lock Washer
❑ Replace after removing
7 - Lock Washer
❑ Replace after removing
❑ Be careful not to damage the cables when removing them
8 - Selector Cable
❑ Attach to the cable retainer
❑ Do not bend
❑ Installed position. Refer to
⇒ “1.1 Selector Mechanism Installation Position”, page 51
9 - Gearshift Cable
❑ Attach to the cable retainer
❑ Do not bend
❑ Installed position. Refer to
⇒ “1.1 Selector Mechanism Installation Position”, page 51
10 - Gearshift Housing
11 - Seal
❑ Between the gearshift housing and the underbody
❑ Replace after removing the gearshift housing
❑ Self-adhesive
❑ Affix to the gearshift housing
12 - Cable Mounting Bracket
❑ Adjust the gearshift mechanism after installing. Refer to
⇒ “1.6 Selector Mechanism, Adjusting”, page 63
13 - Hex Bolt
❑ 20 Nm
❑ For the cable bracket
❑ Quantity: 3
14 - Grommet
❑ Quantity: 3
❑ Cable mounting bracket to transmission
15 - Spacer
❑ Quantity: 3
16 - Nut
❑ Tightening specification. Refer to
⇒ “5.5 Overview - Shift Unit”, page 96
.
17 - Gearshift Lever
❑ Insert so that master spline aligns with shift rod. Refer to
⇒ Fig. ““Installing the Transmission Shift Lever”“ , page 62
❑ Installed position. Refer to
⇒ Fig. ““Selector Lever/Relay Lever Installed Position”“ , page 61
❑ Adjust the gearshift mechanism after installing. Refer to
⇒ “1.6 Selector Mechanism, Adjusting”, page 63
18 - Gearshift Shaft Seal
❑ Replacing. Refer to
⇒ “5.5 Overview - Shift Unit”, page 96
19 - Clip
1.4
Gearshift Knob, Removing and Instal‐
ling
Special tools and workshop equipment required
♦ Hose Clip Pliers - VAG1275A-
♦ Wedge Set - T10383-
♦ Wedge Set - Wedge 1 - T10383/1-
♦ or the equivalent equipment, Backrest Panel Tool - 3370-
Caution
This procedure contains mandatory replaceable parts. Refer
to component overview prior to starting procedure.
Mandatory Replacement Parts
♦ Clamp - Shift Knob to Shift Lever
Removing
– Use the Wedge Set - Wedge 1 - T10383/1- to carefully pry out
the selector lever boot from the center console insert in direc‐
tion of -arrows-.
or
– Open the ashtray.
– Push the Backrest Panel Tool - 3370- as illustrated, under the
plastic frame for the boot in direction of -arrow 1- until stop.
– Remove boot with plastic frame from center console frame
-A- in direction of -arrow 2-
– Roll the selector lever boot up over the gearshift knob.
– Open the clamp -arrow- and remove the gearshift lever knob
with the shift lever boot.
Installing
Install in reverse order of removal. Note the following:
– Press the gearshift knob and the selector lever boot all the way
up on the gearshift lever.
– Secure the gearshift knob with clamp -arrow- on the gearshift
lever (⇒ previous illustration). Use the Hose Clamp Pliers -
VAG1275- to do this.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст