Volkswagen Jetta / Jetta Hybrid. Manual — part 48
and right -arrows a-.
– Press rear bumper cover -1- onto guides on left and right on
side panel until they engage with each other.
– Ensure joints are parallel and shut lines are equal ⇒ Body Re‐
pairs; Rep. gr. 00 ; Body gaps; Body, rear .
– Fit bolts -3-, -4- and -5- in place and tighten them to the re‐
spective specified torque
⇒ page 186
.
– If available, screw in securing bolts of underbody panel at rear
right on bumper cover and tighten to 2.7 Nm.
– Secure loosened/released wheel housing liner in area of
bumper cover
⇒ page 240
.
– Install tail lights in side panel ⇒ Electrical system; Rep. gr.
94 ; Tail lamps; Removing and installing tail lights in side pan‐
el .
2.6
Assembly overview - guides for rear bumper cover
1 - Centre guide
2 - Bolt
❑ Qty. 4.
❑ Specified torque: 4 Nm
3 - Bolt
❑ 2 or 3 bolts per side (de‐
pending on model var‐
iant)
❑ Specified torque: 4 Nm
4 - Bolt
❑ Qty. 5 on each side.
❑ Specified torque: 4 Nm
5 - Guide section at side
❑ Left and right.
6 - Retaining bracket
❑ Left and right.
Jetta 2011 ➤ , Jetta Hybrid 2013 ➤
2. Rear bumper cover
189
1 - Rear bumper carrier
2 - Bolt
❑ Qty. 3 on each side.
❑ Specified torque: 20 Nm
3 - Foam element
❑ Self-adhesive.
❑ Not installed in all model
versions
2.8
Assembly overview - towing bracket
Note
♦
The specified torques refer only to factory-installed towing
brackets.
♦
Request torque specifications for other towing brackets from
relevant manufacturer.
♦
Information on electrics can be found in ⇒ Current flow dia‐
grams, Electrical fault finding and Fitting locations.
Jetta 2011 ➤ , Jetta Hybrid 2013 ➤
190
head
❑ Remove rear bumper
cover
⇒ page 187
.
2 - Bolt
❑ Sealing plugs
❑ Qty. 1 on left
❑ 1 or 2 bolts on right (de‐
pending on model var‐
iant)
❑ Specified torque: 20 Nm
WARNING
The bolts -2- function as
plugs and prevent ex‐
haust gases from enter‐
ing the interior.
The bolts must therefore
always be installed with‐
out fail.
3 - Bolt
❑ Qty. 2 on each side.
❑ Specified torque: 50 Nm
+ turn 120° further
Note
WARNING
Bolts -3- must always be
renewed after being re‐
moved.
Jetta 2011 ➤ , Jetta Hybrid 2013 ➤
2. Rear bumper cover
191
Flush bonded windows
1.1
Tools
Note
The removal of a bonded window is described using the Removal kit for flush bonded windows -V.A.G 1474 A- .
The respective tools from Removal kit for flush bonded windows -VAS 6452- may also be used.
Special tools and workshop
equipment required
♦ Removal kit for flush bon‐
ded windows -
V.A.G 1474 A- or Removal
kit for flush bonded win‐
dows -VAS 6452-
♦ Suction lifter -V.A.G 1344-
♦ Cutting tool -V.A.G 1351-
♦ Windscreen removal kit -
V.A.G 1755-
♦ Cartridge gun -V.A.G 1628-
♦ Cartridge heater -
V.A.G 1939-
Jetta 2011 ➤ , Jetta Hybrid 2013 ➤
192
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст