Volkswagen Jetta / Jetta Hybrid. Manual — part 45
– Ensure joints are parallel and shut lines are equal ⇒ Body Re‐
pairs; Rep. gr. 00 ; Body gaps; Body, front .
– Fit bolts -2-, -3- and -4- in place and tighten them to the re‐
spective specified torque
⇒ page 174
.
– Install radiator grille
⇒ page 261
.
1.6
Front bumper cover add-on parts
Note
Minor differences may be encountered on add-on parts, depending on vehicle model.
1 - Front bumper cover
❑ Material PP/EPDM.
❑ Removing and installing
⇒ page 175
2 - Left trim panel
❑ Pull forwards out of de‐
tent.
❑ Different versions, as‐
signment ⇒ Parts cata‐
logue “ETKA”
3 - Centre air intake grille
❑ Only remove when
bumper cover -1- is re‐
moved
❑ Different versions, as‐
signment ⇒ Parts cata‐
logue “ETKA”
4 - Trim strip
❑ For middle air grille -3-,
depending on model
version
5 - Spoiler
❑ Only remove when
bumper cover -1- is re‐
moved
6 - Registration plate carrier
❑ Is not installed in all
models or in all markets.
❑ Different versions, as‐
signment ⇒ Parts cata‐
logue “ETKA”
7 - Clip
❑ For securing the regis‐
tration plate carrier -6-
8 - Right trim panel
❑ Pull forwards out of detent.
❑ Different versions, assignment ⇒ Parts catalogue “ETKA”
Jetta 2011 ➤ , Jetta Hybrid 2013 ➤
1. Front bumper cover
177
1.7
Installing front number plate carrier
Note
♦
Number plate carrier is not installed in all models or in all markets.
♦
Number plate carriers of different sizes are fitted in various markets.
♦
The height of the number plate carrier is specified by the contour to the bumper.
♦
Adherence to a depth of 12 mm is required when drilling holes.
Carry out following work:
Holes exist
– Position number plate carrier -3- on front bumper cover -2- and
press clips -4- in.
Jetta 2011 ➤ , Jetta Hybrid 2013 ➤
178
– Set drill depth stop to 12 mm and drill holes.
– Position number plate carrier -3- on front bumper cover -2- and
press clips -4- in.
1.8
Assembly overview - guides for front bumper cover
1 - Centre guide
2 - Guide section at side
❑ Left and right.
3 - Bolt
❑ Qty. 2 on each side.
❑ Specified torque: 2 Nm
4 - Bolt
❑ Qty. 3.
❑ Specified torque: 8 Nm
Jetta 2011 ➤ , Jetta Hybrid 2013 ➤
1. Front bumper cover
179
1 - Front bumper carrier
2 - Bolt
❑ Qty. 2 on each side.
❑ Specified torque: 8 Nm
3 - Foam element
❑ Self-adhesive.
❑ Not installed in all model
versions
4 - Nut
❑ Qty. 2.
❑ Specified torque: 8 Nm
5 - Bolt
❑ Qty. 3 on left-hand side
❑ Qty. 4 on right-hand side
❑ Specified torque: 60 Nm
Jetta 2011 ➤ , Jetta Hybrid 2013 ➤
180
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст