Nissan Versa Note. Instruction — part 885
FRONT WIPER DOES NOT OPERATE
WW-59
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
5.
CHECK FRONT WIPER REQUEST SIGNAL INPUT
1. With CONSULT, select FR WIP REQ in DATA MONITOR of IPDM E/R.
2. Switch the front wiper switch to HI and LO.
3. Check the status of FR WIP REQ while operating the switch.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
(with Intelligent Key) or
(without Intelligent Key).
NO
>> GO TO 6.
6.
CHECK COMBINATION SWITCH (WIPER AND WASHER SWITCH)
Check combination switch (wiper and washer switch). Refer to
.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-70, "Removal and Installation"
(with Intelligent Key) or
(without Intelligent Key).
NO
>> Repair or replace the applicable parts.
Data monitor
Condition
Status
FR WIP REQ
Front wiper switch OFF
STOP
Front wiper switch LO
LOW
Front wiper switch HI
HI
WW-60
< SYMPTOM DIAGNOSIS >
NORMAL OPERATING CONDITION
NORMAL OPERATING CONDITION
Description
INFOID:0000000009643042
FRONT WIPER PROTECTION FUNCTION
IPDM E/R detects front wiper stop position by a front wiper stop position signal.
When a front wiper stop position signal is in the conditions listed below, IPDM E/R stops power supply to wiper
after repeating a front wiper 10 seconds activation and 20 seconds stop.
NOTE:
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped.
REAR WIPER MOTOR PROTECTION FUNCTION
• BCM may stop rear wiper to protect the rear wiper motor when the rear wiper is stopped for 5 seconds or
more due to a snowfall.
• Rear wiper operates normally one minute after the obstacles are removed with rear wiper OFF.
Ignition switch
Front wiper switch
Front wiper stop position signal
ON
OFF
The front wiper stop position signal (stop position) cannot be input for 10 seconds.
ON
The front wiper stop position signal does not change for 10 seconds.
WASHER TANK
WW-61
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
REMOVAL AND INSTALLATION
WASHER TANK
Exploded View
INFOID:0000000009578789
Removal and Installation
INFOID:0000000009578790
REMOVAL
1. Remove front under cover. Refer to
EXT-37, "FRONT UNDER COVER : Removal and Installation"
.
2. Remove fender protector (RH). Refer to
EXT-36, "Removal and Installation"
3. Remove washer tank clip (A) using a suitable tool.
1.
Washer tank cap
2.
Washer tank
3.
Front washer motor
A. Front washer motor seal
B. Washer fluid level switch (if equipped)
Front
ALLIA1317ZZ
ALKIA3175ZZ
WW-62
< REMOVAL AND INSTALLATION >
WASHER TANK
4. Release the front washer tube (2) and rear washer tube (1) from
washer tank (3).
5. Release the harness (4) from the washer tank (3).
6. Disconnect the harness connector from the front washer motor.
7. Remove bolts (A) and washer tank (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• After installation, add water to the top of the washer tank inlet to check that no leaks exist.
• Fill washer tank with specified amount of fluid. Refer to
ALLIA1305ZZ
ALLIA1303ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст