Nissan Quest E52. Instruction — part 408
DLK-346
< DTC/CIRCUIT DIAGNOSIS >
SLIDING DOOR OPEN/CLOSE SWITCH
REAR RH : Component Inspection
INFOID:0000000009649294
1.
CHECK SLIDING DOOR OPEN/CLOSE SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect sliding door open/close switch (rear RH) connector.
3.
Check continuity between sliding door open/close switch (rear RH) terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace sliding door open/close switch (rear RH).
Sliding door open/close switch (rear RH)
Condition
Continuity
Terminal
1
2
Sliding door open/close switch
(rear RH)
Pressed
Existed
Released
Not existed
SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH
DLK-347
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH
SLIDING DOOR LH
SLIDING DOOR LH : Component Function Check
INFOID:0000000009649295
1.
CHECK FUNCTION
1.
Select “AUTO SLDE DOOR” using CONSULT.
2.
Select “ONE-TOUCH SW” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Sliding door one-touch open/close switch is OK.
NO
>> Refer to
DLK-347, "SLIDING DOOR LH : Diagnosis Procedure"
SLIDING DOOR LH : Diagnosis Procedure
INFOID:0000000009649296
1.
CHECK SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect sliding door one-touch open/close switch LH connector.
3.
Check voltage between sliding door one-touch open/close switch LH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH CIRCUIT
1.
Disconnect sliding door control unit LH connector.
2.
Check continuity between sliding door control unit LH harness connector and sliding door one-touch open/
close switch LH harness connector.
3.
Check continuity between sliding door control unit LH harness connector and ground.
Is the inspection result normal?
YES
>> Replace sliding door control unit LH. Refer to
DLK-500, "LH : Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH GROUND CIRCUIT
1.
Disconnect sliding door control unit LH connector.
2.
Check continuity between sliding door control unit LH harness connector and sliding door one-touch open/
close switch LH harness connector.
Monitor item
Condition
Status
ONE-TOUCH SW
Sliding door one-touch open/
close switch LH
Pressed
ON
Released
OFF
(+)
(–)
Voltage
Sliding door one-touch open/close switch LH
Connector
Terminal
D125
1
Ground
8 – 16 V
Sliding door control unit LH
Sliding door one-touch open/close switch LH
Continuity
Connector
Terminal
Connector
Terminal
B45
14
D125
1
Existed
Sliding door control unit LH
Ground
Continuity
Connector
Terminal
B45
14
Not existed
DLK-348
< DTC/CIRCUIT DIAGNOSIS >
SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH
3.
Check continuity between sliding door control unit LH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH CIRCUIT 2
1.
Connect sliding door control unit LH connector and sliding door one-touch open/close switch LH connec-
tor.
2.
Check voltage between sliding door one-touch open/close switch LH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace sliding door control unit LH. Refer to
DLK-500, "LH : Removal and Installation"
5.
CHECK SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH
DLK-348, "SLIDING DOOR LH : Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace sliding door one-touch open/close switch LH.
6.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
>> INSPECTION END
SLIDING DOOR LH : Component Inspection
INFOID:0000000009649297
1.
CHECK SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect sliding door one-touch open/close switch LH connector.
3.
Check continuity between sliding door one-touch open/close switch LH terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace sliding door one-touch open/close switch LH.
SLIDING DOOR RH
Sliding door control unit LH
Sliding door one-touch open/close switch LH
Continuity
Connector
Terminal
Connector
Terminal
B45
23
D125
2
Existed
Sliding door control unit LH
Ground
Continuity
Connector
Terminal
B45
23
Not existed
(+)
(–)
Voltage
Sliding door control unit LH
Connector
Terminal
B45
23
Ground
0 V
Sliding door one-touch open/close switch
LH
Condition
Continuity
Terminal
1
2
Sliding door one-touch open/
close switch LH
Pressed
Existed
Released
Not existed
SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH
DLK-349
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
SLIDING DOOR RH : Component Function Check
INFOID:0000000009649298
1.
CHECK FUNCTION
1.
Select “AUTO SLDE DOOR RIGHT” using CONSULT.
2.
Select “ONE-TOUCH SW” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Sliding door one-touch open/close switch is OK.
NO
>> Refer to
DLK-347, "SLIDING DOOR LH : Diagnosis Procedure"
SLIDING DOOR RH : Diagnosis Procedure
INFOID:0000000009649299
1.
CHECK SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect sliding door one-touch open/close switch RH connector.
3.
Check voltage between sliding door one-touch open/close switch RH harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH CIRCUIT
1.
Disconnect sliding door control unit RH connector.
2.
Check continuity between sliding door control unit RH harness connector and sliding door one-touch
open/close switch RH harness connector.
3.
Check continuity between sliding door control unit RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace sliding door control unit RH. Refer to
DLK-500, "RH : Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK SLIDING DOOR ONE-TOUCH OPEN/CLOSE SWITCH GROUND CIRCUIT
1.
Disconnect sliding door control unit RH connector.
2.
Check continuity between sliding door control unit RH harness connector and sliding door one-touch
open/close switch RH harness connector.
Monitor item
Condition
Status
ONE-TOUCH SW
Sliding door one-touch open/
close switch RH
Pressed
ON
Released
OFF
(+)
(–)
Voltage
Sliding door one-touch open/close switch RH
Connector
Terminal
D126
1
Ground
8 – 16 V
Sliding door control unit RH
Sliding door one-touch open/close switch RH
Continuity
Connector
Terminal
Connector
Terminal
B247
14
D126
1
Existed
Sliding door control unit RH
Ground
Continuity
Connector
Terminal
B247
14
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст