Nissan Quest E52. Instruction — part 407
DLK-342
< DTC/CIRCUIT DIAGNOSIS >
SLIDING DOOR OPEN/CLOSE SWITCH
3.
Check voltage between sliding door open/close switch (front side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK SLIDING DOOR OPEN/CLOSE SWITCH CIRCUIT
1.
Disconnect sliding door control unit RH connector.
2.
Check continuity between sliding door control unit RH harness connector and sliding door open/close
switch (front side) harness connector.
3.
Check continuity between sliding door control unit RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace sliding door control unit RH. Refer to
DLK-500, "RH : Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK SLIDING DOOR OPEN/CLOSE SWITCH GROUND CIRCUIT
Check continuity between sliding door open/close switch (front side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK SLIDING DOOR OPEN/CLOSE SWITCH
DLK-342, "FRONT RH : Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace sliding door open/close switch (front side).
5.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
>> INSPECTION END
FRONT RH : Component Inspection
INFOID:0000000009649288
1.
CHECK SLIDING DOOR OPEN/CLOSE SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect sliding door open/close switch (front side) connector.
3.
Check continuity between sliding door open/close switch (front side) terminals.
(+)
(–)
Voltage
Sliding door open/close switch (front side)
Connector
Terminal
M90
1
Ground
8 – 16 V
Sliding door control unit RH
Sliding door open/close switch (front side)
Continuity
Connector
Terminal
Connector
Terminal
B247
19
M90
1
Existed
Sliding door control unit RH
Ground
Continuity
Connector
Terminal
B247
19
Not existed
Sliding door open/close switch (front side)
Ground
Continuity
Connector
Terminal
M90
3
Existed
SLIDING DOOR OPEN/CLOSE SWITCH
DLK-343
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace sliding door open/close switch (front side).
REAR LH
REAR LH : Component Function Check
INFOID:0000000009649289
1.
CHECK FUNCTION
1.
Select “AUTO SLDE DOOR” using CONSULT.
2.
Select “B PILLER SW” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Sliding door open/close switch (rear LH) is OK.
NO
>> Refer to
DLK-343, "REAR LH : Diagnosis Procedure"
.
REAR LH : Diagnosis Procedure
INFOID:0000000009649290
1.
CHECK SLIDING DOOR OPEN/CLOSE SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect sliding door open/close switch (rear LH) connector.
3.
Check voltage between sliding door open/close switch (rear LH) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK SLIDING DOOR OPEN/CLOSE SWITCH CIRCUIT
1.
Disconnect sliding door control unit LH connector.
2.
Check continuity between sliding door control unit LH harness connector and sliding door open/close
switch (rear LH) harness connector.
3.
Check continuity between sliding door control unit LH harness connector and ground.
Sliding door open/close switch (front side)
Condition
Continuity
Terminal
1
3
Sliding door open/close switch
(front RH)
Pressed
Existed
Released
Not existed
Monitor item
Condition
Status
B PILLER SW
Sliding door open/close switch
(rear LH)
Pressed
ON
Released
OFF
(+)
(–)
Voltage
Sliding door open/close switch (rear LH)
Connector
Terminal
B25
1
Ground
8 – 16 V
Sliding door control unit LH
Sliding door open/close switch (rear LH)
Continuity
Connector
Terminal
Connector
Terminal
B45
2
B25
1
Existed
Sliding door control unit LH
Ground
Continuity
Connector
Terminal
B45
2
Not existed
DLK-344
< DTC/CIRCUIT DIAGNOSIS >
SLIDING DOOR OPEN/CLOSE SWITCH
Is the inspection result normal?
YES
>> Replace sliding door control unit LH. Refer to
DLK-500, "LH : Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK SLIDING DOOR OPEN/CLOSE SWITCH GROUND CIRCUIT
Check continuity between sliding door open/close switch (rear LH) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK SLIDING DOOR OPEN/CLOSE SWITCH
DLK-344, "REAR LH : Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace sliding door open/close switch (rear LH).
5.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
>> INSPECTION END
REAR LH : Component Inspection
INFOID:0000000009649291
1.
CHECK SLIDING DOOR OPEN/CLOSE SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect sliding door open/close switch (rear LH) connector.
3.
Check continuity between sliding door open/close switch (rear LH) terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace sliding door open/close switch (rear LH).
REAR RH
REAR RH : Component Function Check
INFOID:0000000009649292
1.
CHECK FUNCTION
1.
Select “AUTO SLDE DOOR RIGHT” using CONSULT.
2.
Select “B PILLER SW” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Sliding door open/close switch (rear RH) is OK.
NO
>> Refer to
DLK-343, "REAR LH : Diagnosis Procedure"
.
Sliding door open/close switch (rear LH)
Ground
Continuity
Connector
Terminal
B25
2
Existed
Sliding door open/close switch (rear LH)
Condition
Continuity
Terminal
1
2
Sliding door open/close switch
(rear LH)
Pressed
Existed
Released
Not existed
Monitor item
Condition
Status
B PILLER SW
Sliding door open/close switch
(rear RH)
Pressed
ON
Released
OFF
SLIDING DOOR OPEN/CLOSE SWITCH
DLK-345
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REAR RH : Diagnosis Procedure
INFOID:0000000009649293
1.
CHECK SLIDING DOOR OPEN/CLOSE SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect sliding door open/close switch (rear RH) connector.
3.
Check voltage between sliding door open/close switch (rear RH) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK SLIDING DOOR OPEN/CLOSE SWITCH CIRCUIT
1.
Disconnect sliding door control unit RH connector.
2.
Check continuity between sliding door control unit RH harness connector and sliding door open/close
switch (rear RH) harness connector.
3.
Check continuity between sliding door control unit RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace sliding door control unit RH. Refer to
DLK-500, "RH : Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK SLIDING DOOR OPEN/CLOSE SWITCH GROUND CIRCUIT
Check continuity between sliding door open/close switch (rear RH) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK SLIDING DOOR OPEN/CLOSE SWITCH
DLK-346, "REAR RH : Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace sliding door open/close switch (rear RH).
5.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
>> INSPECTION END
(+)
(–)
Voltage
Sliding door open/close switch (rear RH)
Connector
Terminal
B206
1
Ground
8 – 16 V
Sliding door control unit RH
Sliding door open/close switch (rear RH)
Continuity
Connector
Terminal
Connector
Terminal
B247
2
B206
1
Existed
Sliding door control unit RH
Ground
Continuity
Connector
Terminal
B247
2
Not existed
Sliding door open/close switch (rear RH)
Ground
Continuity
Connector
Terminal
B206
2
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст