Nissan Juke F15. Instruction — part 742
EXL-188
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
HAZARD SWITCH
HAZARD SWITCH
Component Function Check
INFOID:0000000012201765
1.
CHECK HAZARD SWITCH SIGNAL
With CONSULT
1. Turn ignition switch ON.
2. Select “FLASHER” of “BCM” using CONSULT.
3. Select “HAZARD SW” in “Data Monitor” mode.
4. With operating the hazard switch, check the monitor status.
Is the inspection result normal?
YES
>> Hazard switch circuit is normal.
NO
>> Refer to
EXL-188, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000012201766
1.
CHECK HAZARD SWITCH SIGNAL
1. Turn ignition switch OFF.
2. Disconnect hazard switch connector.
3. Check voltage between hazard switch connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK HAZARD SWITCH SIGNAL CIRCUIT (OPEN)
1. Disconnect BCM connector.
2. Check continuity between hazard switch harness connector and BCM harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK HAZARD SWITCH SIGNAL CIRCUIT (SHORT)
Check continuity between hazard switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
Monitor item
Condition
Monitor status
HAZARD SW
Hazard switch
ON
On
OFF
Off
+
-
Voltage
(Approx.)
Hazard switch
Connector
Terminal
M45
2
Ground
12 V
Hazard switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
M45
2
M68
29
Existed
Hazard switch
—
Continuity
Connector
Terminal
M45
2
Ground
Not existed
HAZARD SWITCH
EXL-189
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
NO
>> Repair or replace harness.
4.
CHECK HAZARD SWITCH GROUND CIRCUIT
Check continuity between hazard switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace hazard switch. Refer to
EXL-218, "Removal and Installation"
NO
>> Repair or replace harness.
Hazard switch
—
Continuity
Connector
Terminal
M45
1
Ground
Existed
EXL-190
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
EXTERIOR LIGHTING SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
EXTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000012201767
EXCEPT FOR NISMO MODELS
Without Daytime Running Light System
NOTE:
Perform the self-diagnosis with CONSULT before the symptom diagnosis. Perform the trouble diagnosis if any
DTC is detected.
Symptom
Possible cause
Inspection item
Headlamp (HI) is not turned
ON
One side
• Fuse
• Headlamp (HI) power supply/
ground circuit
• Headlamp (HI) bulb
• Headlamp assembly
- Harness
• IPDM E/R
Headlamp (HI) circuit
Refer to
Both sides
Symptom diagnosis
“BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to
EXL-198, "Diagnosis Procedure"
High beam indicator lamp is not turned ON
[Headlamp (HI) is turned ON]
Combination meter
• Combination meter
Data monitor “HI-BEAM IND”
• BCM (HEAD LAMP)
Active test “HEAD LAMP”
Headlamp (LO) is not
turned ON
One side
• Fuse
• Headlamp (LO) power supply/
ground circuit
• Headlamp (LO) bulb
(Xenon bulb)
• Headlamp assembly
- HID control unit
- Xenon bulb socket
- Harness
• IPDM E/R
Headlamp (LO) circuit
Refer to
Both sides
Symptom diagnosis
“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to
EXL-199, "Diagnosis Procedure"
Each lamp is not turned ON/OFF with lighting switch
AUTO
• Combination switch input/output
signal circuit
• Combination switch
• BCM
Combination switch
Refer to
.
• Optical sensor power supply/
ground/signal circuit
• Optical sensor
• BCM
Optical sensor
Refer to
Parking lamp is not turned ON
• Parking lamp power supply/
ground circuit
• Front combination lamp
- LED (Parking lamp)
- Harness
• IPDM E/R
Parking lamp circuit
Refer to
Front side marker lamp is not turned ON
• Front side marker lamp power
supply/ground circuit
• Front side marker lamp bulb
• Front side marker lamp bulb sock-
et
Front side marker lamp circuit
Refer to
EXTERIOR LIGHTING SYSTEM SYMPTOMS
EXL-191
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Tail lamp is not turned ON
Stop lamp / Tail lamp
(Bulb side)
• Fuse
• Tail lamp power supply/ground
circuit
• Stop lamp / Tail lamp bulb
• Stop lamp / Tail lamp bulb socket/
harness
• IPDM E/R
Tail lamp (LED side)
• Fuse
• Tail lamp power supply/ground
circuit
• Rear combination lamp internal
circuit
- LED (Tail lamp)
• Tail lamp harness
• IPDM E/R
License plate lamp is not turned ON
• License plate lamp power supply/
ground circuit
• License plate lamp bulb
• License plate lamp bulb socket/
harness
License plate lamp circuit
Refer to
Parking lamp, license plate lamp, side marker lamp and
tail lamp are not turned ON
Symptom diagnosis
“PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT
TURNED ON”
Refer to
EXL-200, "Diagnosis Procedure"
Position lamp indicator is not turned ON
(Parking lamp, license plate lamp, side marker lamp
and tail lamp are turned ON)
Combination meter
• Combination meter
Data monitor “LIGHT IND”
• BCM (HEAD LAMP)
Active test “TAIL LAMP”
Front fog lamp is not turned
ON
One side
• Front fog lamp power supply/
ground circuit
• Front fog lamp bulb
• IPDM E/R
Front fog lamp circuit
Refer to
Both sides
Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to
EXL-201, "Diagnosis Procedure"
Turn signal lamp does not
blink
Indicator lamp is normal
(Applicable side per-
forms high flasher activa-
tion)
• Front turn signal lamp
- Front turn signal lamp power sup-
ply/ground circuit
- Front turn signal lamp bulb
- Front turn signal lamp bulb socket
- BCM
• Side turn signal lamp
- Side turn signal lamp power sup-
ply/ground circuit
- Side turn signal lamp
- BCM
• Rear turn signal lamp
- Rear turn signal lamp power sup-
ply/ground circuit
- Rear turn signal lamp bulb
- Rear turn signal lamp bulb socket/
harness
- BCM
Turn signal lamp circuit
Refer to
Indicator lamp is included
• Combination switch input/output
signal circuit
• Combination switch
• BCM
Combination switch
Refer to
Symptom
Possible cause
Inspection item
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст