Nissan Juke F15. Instruction — part 741
EXL-184
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
TURN SIGNAL LAMP CIRCUIT
5.
CHECK TURN SIGNAL LAMP BULB
Check the applicable turn signal lamp bulb.
Is the inspection result normal?
YES-1 >> Front turn signal lamp: Check the corresponding front turn signal lamp bulb socket. Repair or
replace if necessary.
YES-2 >> Rear turn signal lamp: Check the corresponding rear turn signal lamp bulb socket and harness.
Repair or replace if necessary.
NO
>> Replace the corresponding turn signal lamp bulb. Refer to
(front turn sig-
nal lamp) or
OPTICAL SENSOR
EXL-185
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
OPTICAL SENSOR
Component Function Check
INFOID:0000000012201763
1.
CHECK OPTICAL SENSOR SIGNAL
With CONSULT
1. Turn ignition switch ON.
2. Select “HEAD LAMP” of “BCM” using CONSULT.
3. Select “OPTI SEN (DTCT)” in “Data Monitor” mode.
4. Turn lighting switch AUTO.
5. With the optical sensor illuminating, check the monitor status.
*: Illuminates the optical sensor. The value may be less than the standard value if brightness is weak.
Is the inspection result normal?
YES
>> Optical sensor is normal.
NO
>> Refer to
EXL-185, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000012201764
1.
CHECK OPTICAL SENSOR POWER SUPPLY
1. Turn ignition switch ON.
2. Turn lighting switch AUTO.
3. Check voltage between optical sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK OPTICAL SENSOR GROUND
Check voltage between optical sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 6.
3.
CHECK OPTICAL SENSOR SIGNAL
With illuminating the optical sensor, check voltage between optical sensor harness connector and ground.
Monitor item
Condition
Voltage
(Approx.)
OPTI SEN (DTCT) Optical sensor
When illuminating
3.1 V or more *
When shutting off light
0.6 V or less
+
-
Voltage
(Approx.)
Optical sensor
Connector
Terminal
M84
1
Ground
5 V
+
-
Voltage
(Approx.)
Optical sensor
Connector
Terminal
M84
3
Ground
0 V
EXL-186
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
OPTICAL SENSOR
*: Illuminate the optical sensor. The value may be less than the standard if brightness is weak.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Replace optical sensor. Refer to
EXL-216, "Removal and Installation"
4.
CHECK OPTICAL SENSOR POWER SUPPLY CIRCUIT (OPEN)
1. Turn ignition switch OFF.
2. Disconnect optical sensor connector and BCM connector.
3. Check continuity between optical sensor harness connector and BCM harness connector.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK OPTICAL SENSOR POWER SUPPLY CIRCUIT (SHORT)
Check continuity between optical sensor harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace harness.
6.
CHECK OPTICAL SENSOR GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect optical sensor connector and BCM connector.
3. Check continuity between optical sensor harness connector and BCM harness connector.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace harness.
7.
CHECK OPTICAL SENSOR SIGNAL CIRCUIT (OPEN)
1. Turn ignition switch OFF.
2. Disconnect optical sensor connector and BCM connector.
3. Check continuity between optical sensor harness connector and BCM harness connector.
+
-
Condition
Voltage
(Approx.)
Optical sensor
Connector
Terminal
M84
2
Ground
Optical sensor
When illuminating
3.1 V or more*
When shutting off light
0.6 V or less
Optical sensor
BCM
Continuity
Connector
Terminal
Connector
Terminal
M84
1
M68
17
Existed
Optical sensor
—
Continuity
Connector
Terminal
M84
1
Ground
Not existed
Optical sensor
BCM
Continuity
Connector
Terminal
Connector
Terminal
M84
3
M68
18
Existed
OPTICAL SENSOR
EXL-187
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Is the inspection result normal?
YES
>> GO TO 8.
NO
>> Repair or replace harness.
8.
CHECK OPTICAL SENSOR SIGNAL CIRCUIT (SHORT)
Check continuity between optical sensor harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace harness.
Optical sensor
BCM
Continuity
Connector
Terminal
Connector
Terminal
M84
2
M68
14
Existed
Optical sensor
—
Continuity
Connector
Terminal
M84
2
Ground
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст