Nissan Juke F15. Instruction — part 740
EXL-180
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
FRONT FOG LAMP CIRCUIT
FRONT FOG LAMP CIRCUIT
Component Function Check
INFOID:0000000012201759
1.
CHECK FRONT FOG LAMP OPERATION
With CONSULT
1. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.
2. With operating the test items, check that the front fog lamp is turned ON.
Without CONSULT
1. Start IPDM E/R auto active test. Refer to
PCS-12, "Diagnosis Description"
2. Check that the front fog lamp is turned ON.
Is the measurement normal?
YES
>> Front fog lamp circuit is normal.
NO
>> Refer to
EXL-180, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000012201760
1.
CHECK FRONT FOG LAMP FUSE
1. Turn ignition switch OFF.
2. Check that the following fuses are not blown (open).
Is the fuse blown (open)?
YES
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown (open).
NO
>> GO TO 2.
2.
CHECK FRONT FOG LAMP POWER SUPPLY
With CONSULT
1. Disconnect front fog lamp connector.
2. Turn ignition switch ON.
3. Select “EXTERNAL LAMPS” in “Active Test” mode of “IPDM E/R” using CONSULT.
4. With operating the test items, check the voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace IPDM E/R. Refer to
PCS-37, "Removal and Installation"
3.
CHECK FRONT FOG LAMP POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and front fog lamp harness connector.
Fog
: Front fog lamp ON
Off
: Front fog lamp OFF
Unit
Location
Fuse No.
Capacity
Front fog lamp
IPDM E/R
#50
15 A
+
-
Test item
Voltage
IPDM E/R
Connector
Terminal
RH
E12
19
Ground
EXTERNAL
LAMPS
Fog
9 – 16 V
Off
0 – 1 V
LH
20
Fog
9 – 16 V
Off
0 – 1 V
FRONT FOG LAMP CIRCUIT
EXL-181
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK FRONT FOG LAMP GROUND CIRCUIT
Check continuity between front fog lamp harness connector and ground.
Is the inspection result normal?
YES
>> Replace the corresponding front fog lamp bulb. Refer to
NO
>> Repair or replace harness.
IPDM E/R
Front fog lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E12
19
E48
1
Existed
LH
20
E30
Front fog lamp
—
Continuity
Connector
Terminal
RH
E48
2
Ground
Existed
LH
E30
EXL-182
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
TURN SIGNAL LAMP CIRCUIT
TURN SIGNAL LAMP CIRCUIT
Component Function Check
INFOID:0000000012201761
1.
CHECK TURN SIGNAL LAMP OPERATION
With CONSULT
1. Turn ignition switch ON.
2. Select “FLASHER” of “BCM” using CONSULT.
3. Select “FLASHER” in “Active Test” mode.
4. With operating the test items, check that the turn signal lamps is turned ON.
Is the inspection result normal?
YES
>> Turn signal lamp circuit is normal.
NO
>> Refer to
EXL-182, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000012201762
1.
CHECK TURN SIGNAL LAMP POWER SUPPLY
With CONSULT
1. Turn ignition switch OFF.
2. Disconnect the following connectors.
-
Front turn signal lamp
-
Door mirror
-
Rear combination lamp
3. Turn ignition switch ON.
4. Select “FLASHER” of “BCM” using CONSULT.
5. Select “FLASHER” in “Active Test” mode.
6. With operating the test items, check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK TURN SIGNAL LAMP POWER SUPPLY CIRCUIT (SHORT)
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and ground.
Is the inspection result normal?
RH
: Turn signal lamps (RH) ON
LH
: Turn signal lamps (LH) ON
Off
: Turn signal lamps OFF
+
-
Test item
Voltage
BCM
Connector
Terminal
RH
M69
61
Ground
FLASHER
RH
9 – 16 V
Off
0 V
LH
60
LH
9 – 16 V
Off
0 V
BCM
—
Continuity
Connector
Terminal
RH
M69
61
Ground
Not existed
LH
60
TURN SIGNAL LAMP CIRCUIT
EXL-183
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
YES
>> Replace BCM. Refer to
BCS-94, "Removal and Installation"
NO
>> Repair or replace harness.
3.
CHECK TURN SIGNAL LAMP POWER SUPPLY CIRCUIT (OPEN)
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM harness connector and each turn signal lamp harness connector.
Front turn signal lamp
Side turn signal lamp
Rear turn signal lamp
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK TURN SIGNAL LAMP GROUND CIRCUIT
Check continuity between each turn signal lamp harness connector and ground.
Front turn signal lamp
Side turn signal lamp
Rear turn signal lamp
Is the inspection result normal?
YES-1 >> Front turn signal lamp or rear turn signal lamp: GO TO 5.
YES-2 >> Side turn signal lamp: Replace the corresponding side turn signal lamp. Refer to
.
NO
>> Repair or replace harness.
BCM
Front turn signal lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
M69
61
E47
1
Existed
LH
60
E34
BCM
Door mirror
Continuity
Connector
Terminal
Connector
Terminal
RH
M69
61
D9
13
Existed
LH
60
D30
BCM
Rear combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
M69
61
B59
5
Existed
LH
60
B80
Front turn signal lamp
—
Continuity
Connector
Terminal
RH
E47
2
Ground
Existed
LH
E34
Door mirror
—
Continuity
Connector
Terminal
RH
D9
2
Ground
Existed
LH
D30
Rear combination lamp
—
Continuity
Connector
Terminal
RH
B59
3
Ground
Existed
LH
B80
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст