Hyundai Santa Fe (2006 year). Manual — part 790
REAR SUSPENSION SYSTEM
SS -67
11. Remove the rear cross member.
12. Remove the rear stabilizer bar link (A) and bracket (B).
B
C
D
A
SCMSS6020D
13. Remove the rear stabilizer bar.
INSPECTION
ECE1FBDC
1.
Check the bushing for wear and deterioration.
2.
Check the stabilizer bar for bending or breakage.
3.
Check the ball joint dust cover for cracks.
4.
Check all bolts.
INSTALLATION
EF4C9769
1.
Install the bushing (B) on the stabilizer bar (A).
A
C
B
D
SCMSS6021D
NOTE
Bring clamp (C) of stabilizer bar (A) into contact with
bushing (B).
2.
Install the bracket (D) on the bushing (B).
3.
Install the rear stabilizer bar to the rear cross member.
4.
Install the rear stabilizer bar bracket (B) and link (A).
Tightening torque Nm (kgf-m, lb-ft) :
Nut(C) : 44.1~53.9 (4.5~5.5, 32.5~39.8)
Nut(D) : 58.8~78.5 (6.0~8.0, 43.4~57.9)
B
C
D
A
SCMSS6020D
5.
Install the rear cross member.
SS -68
SUSPENSION SYSTEM
6.
Support the rear cross member assembly (A) with the
jack.
A
SCMSS6010D
7.
Install the rear cross member mounting bolts (A), nuts
(B) and plate (C).
Tightening torque Nm (kgf-m, lb-ft) :
Bolts(A) : 156.9~176.5 (16~18, 115.7~130.2)
Nuts(B) : 156.9~176.5 (16~18, 115.7~130.2)
A
C
SCMSS6012D
B
C
SCMSS6013D
8.
Install the rear cross member stay (A) and mounting
bolt (B) and nut (C).
Tightening torque Nm (kgf-m, lb-ft) :
Bolt(B) : 68.6~88.3 (7~9, 50.6~65.1)
Nut(C) : 68.6~88.3 (7~9, 50.6~65.1)
B
A
C
SCMSS6011D
9.
After matching a match mark (C) on the rubber cou-
pling (A) and rear differential companion (B), Install
the propeller shaft mounting bolts (D).
Tightening torque Nm (kgf-m, lb-ft) :
49.0~68.6 (5~7, 36.2~50.6)
A
D
C
B
SCMSS6518D
REAR SUSPENSION SYSTEM
SS -69
10. Install the wheel speed sensor (A) and the parking
brake cable (B) to the rear axle carrier.
Tightening torque Nm (kgf-m, lb-ft) :
Wheel speed sensor (A) :
6.9~10.8 (0.7~1.1, 5.1~8.0)
A
B
SCMSS6517D
11. Install the brake caliper (B), then tighten the brake
caliper mounting bolts (A).
Tightening torque Nm (kgf-m, lb-ft) :
63.7~73.5 (6.5~7.5, 47.0~54.2)
A
B
SCMSS6515D
12. Support the rear lower arm with a jack as shown in
the illustration.
SCMSS6526D
13. Install the rear shock absorber (A).
Tightening torque Nm (kgf-m, lb-ft) :
Bolt(B) : 137.3~156.9 (14~16, 101.3~115.7)
Nut(C) : 98.1~117.7 (10.0~12.0, 72.3~86.8)
A
C
B
SCMSS6527D
SS -70
SUSPENSION SYSTEM
NOTE
After checking the distance(453±10mm(17.83
±0.39in)) between the wheel housing garnish (A) and
the hub assembly (B) as shown in the illustration,
tighten the mounting bolts and nuts of rear chassis
part with specified torque.
A
B
453 10 mm
SCMSS6528D
14. Install the wheel and tire (A) to the rear hub (B).
Tightening torque Nm (kgf-m, lb-ft) :
88.3~107.9 (9~11, 65.1~79.6)
A
B
C
SCMSS6512D
CAUTION
Be careful not to damage the hub bolts (C) when
installing the rear wheel and tire (A).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст