Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 95
Symptom:
*HIGH BEAM INDICATOR ALWAYS ON
POSSIBLE CAUSES
DIMMER SWITCH HIGH BEAM OUTPUT CIRCUIT SHORT TO VOLTAGE
JUNCTION BLOCK SHORT TO VOLTAGE
MULTI- FUNCTION SWITCH
BODY CONTROL MODULE
INSTRUMENT CLUSTER
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t in Body Control Inputs/Outputs, read the Hi Beams state.
Does the DRBIII
t Inputs/Outputs, display On?
All
Yes
→ Go To 2
No
→ Replace the Instrument Cluster in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
2
Turn the ignition off.
Disconnect the Multi- Function Switch harness connector.
Turn the ignition on.
With the DRBIII
t in Body Control Inputs/Outputs, read the Hi Beams state.
Does the DRBIII
t display On?
All
Yes
→ Go To 3
No
→ Replace the Multi- Function Switch in accordance with the
Service Information.
Perform BODY VERIFICATION TEST - VER 1.
3
Turn the ignition off.
Disconnect the Multi- Function Switch harness connector.
Disconnect the Junction Block C6 harness connector.
Turn the ignition on.
Measure the voltage between the Dimmer Switch High Beam Output circuit and
ground.
Is there any voltage present?
All
Yes
→ Repair the Dimmer Switch High Beam Output circuit between
the Multi- Function Switch and the Junction Block for a short to
voltage.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 4
365
INSTRUMENT CLUSTER
TEST
ACTION
APPLICABILITY
4
Turn the ignition off.
Disconnect the Junction Block C6 harness connector.
Turn the ignition on.
Measure the voltage between the #3 Fuse in the Junction Block and ground.
Is there any voltage present?
All
Yes
→ Replace the Junction Block in accordance with the Service Infor-
mation.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Body Control Module in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
366
INSTRUMENT CLUSTER
*HIGH BEAM INDICATOR ALWAYS ON —
Continued
Symptom:
*HIGH BEAM INDICATOR INOPERATIVE
POSSIBLE CAUSES
INDICATOR BULB
DIMMER SWITCH HIGH BEAM OUTPUT CIRCUIT OPEN
BODY CONTROL MODULE
JUNCTION BLOCK
MULTI- FUNCTION SWITCH OPEN
INSTRUMENT CLUSTER
TEST
ACTION
APPLICABILITY
1
NOTE: Ensure that the Junction Block Fuse #11 is not open. If the fuse is
open make sure to check for a short to ground.
NOTE: Ensure that the Exterior High Beam Headlamps operate properly
before proceeding with this test.
Turn the ignition on.
With the DRBIII
t in MIC Actuators, actuate the Hi Beam Lamp.
Did the High Beam Indicator illuminate?
All
Yes
→ Go To 2
No
→ Go To 6
2
Turn the ignition on.
With the DRBIII
t in Body Control Inputs/Outputs, read the Hi Beams state while
actuating the High Beam Headlamps.
Does the DRBIII
t Inputs/Outputs display On?
All
Yes
→ Replace the Instrument Cluster in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 3
3
Turn the ignition off.
Disconnect the Junction Block C6 harness connector.
Actuate the High Beam Headlamps.
Measure the voltage between the Dimmer Switch High Beam Output circuit and
ground at the Junction Block C6 harness connector.
Is the voltage above 10.5 volts?
All
Yes
→ Go To 4
No
→ Go To 5
367
INSTRUMENT CLUSTER
TEST
ACTION
APPLICABILITY
4
Turn the ignition off.
Disconnect and isolate the Negative Battery cable.
Disconnect the Junction Block C6 harness connector.
Disconnect the BCM from the Junction Block.
Using the Wiring Diagrams as a guide, measure the resistance of the Dimmer Switch
High Beam Output circuit through the Junction Block.
Is the resistance above 10 ohms?
All
Yes
→ Replace the Junction Block in accordance with the Service Infor-
mation.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Body Control Module in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
5
Turn the ignition off.
Disconnect the Junction Block C6 harness connector.
Disconnect the Multi- Function Switch harness connector.
Measure the resistance of the Dimmer Switch High Beam Output circuit.
Is the resistance above 5.0 ohms?
All
Yes
→ Repair the Dimmer Switch High Beam Output circuit between
the Multi- Function Switch and the Junction Block for an open.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Multi- Function Switch in accordance with the
Service Information.
Perform BODY VERIFICATION TEST - VER 1.
6
Turn the ignition off.
Remove and inspect the High Beam Indicator bulb and socket.
Is the bulb or socket defective?
All
Yes
→ Replace the High Beam Indicator Bulb or socket in accordance
with the Service Information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Instrument Cluster in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
368
INSTRUMENT CLUSTER
*HIGH BEAM INDICATOR INOPERATIVE —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст