SsangYong Korando II (1996-2006 year). Manual — part 38
1D1 -- 14 M162 ENGINE COOLING
DAEWOO MY_2000
COOLING FAN SHROUD
1 Clip
2 Lower Fan Shroud
3 Bolt
4 Fan Shroud Assembly
5 Radiator
Removal & Installation Procedure
1. Pull out the 2 clips (1) from the fan shroud assembly.
2. Remove the lower fan shroud (2).
Notice: For installation, exactly align the lower fan
shroud pin into the hole of the fan shroud assembly (4)
and insert the clips.
3. Remove the bolts (3) and then remove the cooling fan
shroud assembly (4).
Installation Notice
Tightening Torque
3 -- 7 NSm (27 -- 62 lb-in)
4. Installation should follow the removal procedure in
the reverse order.
M162 ENGINE COOLING 1D1 -- 15
DAEWOO MY_2000
RADIATOR
Preceding Work: Removal of cooling fan shroud
1 Radiator Inlet Coolant Hose
2 Radiator Outlet Coolant Hose
3 Make Up Coolant Hose
4 Automatic Transmission Oil Cooling Line
5 Automatic Transmission Oil Cooling Line
4 Bolt
3--7 NSm (27--62 lb-in)
. . . . . . . . . . . . . . . . . .
7 Insulator
8 Stopper
4 Bolt
7 NSm (62 lb-in)
. . . . . . . . . . . . . . . . . . . . . . .
10 Radiator
1D1 -- 16 M162 ENGINE COOLING
DAEWOO MY_2000
Removal & Installation Procedure
1. Drain coolant from the radiator.
2. Remove the coolant thermo connector from the ra-
diator.
3. Remove the each coolant hoses.
4. Remove the upper and lower automatic transmis-
sion fluid cooler pipes from radiator.
Installation Notice
Tightening Torque
20 NSm (15 lb-ft)
5. Remove the mounting bolt (9) from the automatic
transmission radiator tube assembly (5) and then
disconnect the tube assembly (5).
Installation Notice
Tightening Torque
7 NSm (62 lb-in)
6. Remove the mounting bolt (6) on the radiator brack-
et (8) and take off the bracket (8) and insulator (7).
Installation Notice
Tightening Torque
3 -- 7 NSm (27 -- 62 lb-in)
7. Remove the radiator (10).
8. Check the radiator pin for crack, damage, leakage
and bending and replace it if necessary.
9. Installation is reverse order of removal.
10. Check for leakage in the cooling system.
DAEWOO MY_2000
SECTION 1E1
M162 ENGINE ELECTRICAL
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless other-
wise noted.
TABLE OF CONTENTS
Specifications
1E1--2
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Generator Specifications
1E1--2
. . . . . . . . . . . . . . . . . .
Starting Motor Specifications
1E1--2
. . . . . . . . . . . . . . .
Battery Specifications
1E1--2
. . . . . . . . . . . . . . . . . . . . .
Fastener Tightening Specifications
1E1--2
. . . . . . . . . .
Maintenance and Repair
1E1--3
. . . . . . . . . . . . . . . . . . .
On--Vehicle Service
1E1--3
. . . . . . . . . . . . . . . . . . . . . . . . .
Generator
1E1--3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting Motor
1E1--4
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery
1E1--5
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spark Plug
1E1--6
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ignition Cable
1E1--8
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unit Repair
1E1--11
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery
1E1--11
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст