SsangYong Korando II (1996-2006 year). Manual — part 36
1D1 -- 6 M162 ENGINE COOLING
DAEWOO MY_2000
6. Remove the de--aeration hose clamp in the coolant
pump and remove the de--aeration hose.
7. Fill up the coolant through the coolant reservoir
tank.
Notice
D
Match the anti--freeze and the water ratio to 50 : 50.
D
Supplement the coolant until the coolant overflows to
the deaeration hose.
8. Insert the de--aeration hose and completely tighten
the clamp.
9. Check the coolant level in the coolant reservoir tank.
10. Warm up(until thermostat is opened) the engine and
recheck the coolant level in the reservoir tank and fill
up the coolant if necessary.
M162 ENGINE COOLING 1D1 -- 7
DAEWOO MY_2000
COOLANT CONNECTION FITTING
Preceding Work: Removal of cooling fan shroud
1 Bolt (M8 X 100, 2 pieces)
22.5--27.5 NSm (16.6--20.3 lb-ft)
. . . . . . . . . . . . .
2 Engine Hanger Bracket
3 Coolant Outlet Port
4 O--ring
5 Hose Mounting Clamp
6 Hose
Removal & Installation Procedure
1. Drain coolant from the radiator.
2. Remove the hose mounting clamp (5) and disconnect
the coolant hose (6).
3. Remove the two bolts (1), the engine hanger bracket
(2) and coolant outlet port (3).
Installation Notice
Tightening Torque
22.5 -- 27.5 NSm
(16.6 -- 20.3 lb-ft)
Replace the O--ring with new one.
4. Installation should follow the removal procedure in
the reverse order.
5. Fill up the coolant as specified.
6. Check the leaks in the cooling system.
1D1 -- 8 M162 ENGINE COOLING
DAEWOO MY_2000
WATER PUMP
Preceding Work: Removal of V--belt
Removal of air admission housing
1 Air Admission Housing
2 Oil Cooler Pipe Line
3 Seal
Replace
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 Bolt
9--11 NSm (80--97 lb-in)
. . . . . . . . . . . . . . . . .
5 Coolant Hose
6 Coolant Hose
7 Outlet Coolant Hose
8 Coolant Hose
9 Inlet Coolant Hose
10 Water Pump
11 Bolt
21 NSm (15 lb-ft)
. . . . . . . . . . . . . . . . . . . . . .
12 Dowel Sleeve
13 Seal
Replace
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
M162 ENGINE COOLING 1D1 -- 9
DAEWOO MY_2000
Removal & Installation Procedure
1. Drain the coolant.
2. Disconnect the water pump wire connector.
3. Loosen the hose clip and dsconnect all hoses from
the water pump.
4. Remove the oil cooler pipe line bolts (4) and then re-
move the coolant line (2).
Installation Notice
Tightening Torque
9 -- 11 NSm (80 -- 97 lb-in)
Notice: Replace the seal (3).
5. Remove the mounting bolts (11) and carefully pull out
water pump (10).
Installation Notice
Tightening Torque
21 NSm (15 lb-ft)
Notice: Replace the seal (13).
6. Installation should follow the removal procedure in
the reverse order.
7. Fill up coolant.
8. Do coolant system leakage test.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст