SsangYong Korando II (1996-2006 year). Manual — part 35
1D1 -- 2 M162 ENGINE COOLING
DAEWOO MY_2000
SPECIFICATIONS
GENERAL SPECIFICATIONS
Application
Description
Cooling Type
Water Cooling Forced Circulation
Radiator
Circulation Type
Double Cross Flow
Radiation Capability
70,000 kcal/h
Dimension(Width x Height x Thickeness)
580 x 482 x 45 mm
Cooling Fan
φ 460, Six Blades
Anti--Freeze Agent
ALUTEC -- P78
Mixing Ratio of Anti--Freeze Agen with Water (Anti--Freeze Agent : Water)
50 : 50
Coolant Capacity
11.3 L
Reservoir Capacity
3.4 L
Cap Operating Pressure (Reservoir Tank Pressure Cap)
1.4 bar
FASTENER TIGHTENING SPECIFICATIONS
Application
NSm
Lb-Ft
Lb-In
Coolant Drain Plug
30
22
--
Engine Hanger Bracket and Coolant Outlet
Port Bolt
22.5 -- 27.5
16.6 -- 20.3
--
Thermostat Cover Bracket Bolts
9 -- 11
--
80 -- 97
Oil Cooler Pipe Line Bolts
9 -- 11
--
80 -- 97
Cooling Fan Bolts
9 -- 11
--
80 -- 97
Viscous Clutch Mounting Bolts
40.5 -- 49.5
29.8 -- 36.5
--
Automatic Transmission Fluid Cooler Pipe
20
15
--
Cooling Fan Shroud Bolts
3 -- 7
--
27 -- 62
Automatic Transmission Radiator Tube
Assembly Mounting Bolt
7
--
62
Radiator Bracket Mounting Bolts
3 -- 7
--
27 -- 62
M162 ENGINE COOLING 1D1 -- 3
DAEWOO MY_2000
SPECIAL TOOLS AND EQUIPMENT
SPECIAL TOOLS TABLE
124 589 15 21 00
Tester
603 589 00 40 00
Fan Clutch Holder
1D1 -- 4 M162 ENGINE COOLING
DAEWOO MY_2000
DIAGNOSIS
SYSTEM LEAKAGE TEST
Tools Required
124 589 15 21 00
Tester
Test Procedure
1. Loosen the cap a little and release pressure and re-
move the cap.
Notice: For the risk of scalding, cap must not be opened
unless the coolant temperature is below 90°C.
2. Fill coolant up to upper edge (arrow) of reservoir.
3. Connect the special tool to the reservoir filler cap and
apply 1.4 bar of pressure.
Tester 124 589 15 21 00
4. If the pressure on the tester drops, check leakage at
the all coolant hoses and pipes and each connec-
tions. Replace or retighten if necessary.
M162 ENGINE COOLING 1D1 -- 5
DAEWOO MY_2000
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
COOLANT DRAIN AND FILL UP
Draning & Filling up Procedure
1. Loosen the cap a little and release pressure and re-
move the cap.
Notice: For the risk of scalding, the cap must not be
opened unless the coolant temperature is below 90°C.
2. Loosen the radiator lower drain cock and drain the
coolant.
Notice: Collect the coolant by using a proper container.
3. Drain the coolant from the crankcase by inserting a
hose (dia. 14mm) onto the drain bolt on the side of
crankcase (exhaust manifold) and by loosening the
plug.
Notice
D
Just loosen the drain plug to drain the coolant and do
not remove the plug completely.
D
Collect the coolant by using the proper container.
4. After complete draining of the coolant, remove the
hose connector to drain plug and reinstall the drain
plug.
Installation Notice
Tightening Torque
30 NSm (22 lb-ft)
5. Tighten the radiator lower drain cock.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст