Isuzu KB P190. Manual — part 84

3C-16 FRONT SUSPENSION

Stabilizer Bar

Stabilizer Bar and Associated Parts

RTW340LF000901

Legend

(1) Stabilizer Bar

(2) Link

(3) Link Nut

(4) Link Nut

(5) Bracket and Bolt

(6) Rubber Bushing

Removal

1. Raise the vehicle and support the frame with

suitable safety stands.

2. Remove wheel and tire assembly. Refer to Wheel

Replacement in this section.

3. Remove link nut.

CAUTION: Be careful not to damage the ball joint
boot.

4. Remove link.

5. Remove bracket and bolt.

6. Remove stabilizer bar.

7. Remove rubber bushing.

FRONT SUSPENSION 3C-17

Inspection and Repair

Make the necessary adjustments or parts replacement
if wear, damage, corrosion or any other abnormal
condition is found during inspection.

Check the following parts:

• Stabilizer bar
• Rubber bushing
• Link ball joint

Installation

1. Install rubber bushing.

2. Install stabilizer bar.

3. Install bracket and bolt then tighten it to the

specified torque.

Torque: 25 N

⋅⋅⋅⋅m (2.5 kgf⋅⋅⋅⋅m/18 lb⋅ft)

4. Install link.

5. Install link nut, then tighten it to the specified

torque.

Torque: 50 N

⋅⋅⋅⋅m (5.1 kgf⋅⋅⋅⋅m/37 lb⋅ft)

3C-18 FRONT SUSPENSION

Knuckle

Knuckle and Associated Parts

450R300037

Legend

(1) Nut and Cotter Pin

(2) Back Plate

(3) Nut and Cotter Pin

(4) Nut and Cotter Pin

(5) Knuckle

(6) Bolt

Removal

1. Raise the vehicle and support the frame with

suitable safety stands.

2. Remove wheel and tire assembly. Refer to Wheel

in this section.

3. Remove the brake caliper. Refer to Disc Brakes in

Brake section.

4. Remove the hub assembly. Refer to Front Hub

and Disk in this section.

5. Remove tie-rod end from the knuckle. Refer to

Power Steering Unit in Steering section.

FRONT SUSPENSION 3C-19

6. Remove the stabilizer link nuts. Right and left.

7. Remove the wheel speed sensor from the knuckle.

8. Remove back plate.

9. Remove lower ball joint by using remover 5-8840-

2017-0.

CAUTION: Be careful not to damage the ball joint
boot.

P1010009

10. Remove upper ball joint by using remover 5-8840-

2017-0.

CAUTION: Be careful not to damage the ball joint
boot.

P1010011

11. Remove knuckle.

Inspection and Repair

Make the necessary adjustments or parts replacement
if wear, damage, corrosion or any other abnormal
condition is found during inspection.

Check the following parts:

• Knuckle
• Knuckle arm

Installation

1. Install knuckle assembly.

2. Install upper ball joint and tighten the nut to the

specified torque, with just enough additional torque

to align cotter pin holes. Install new cotter pin.

Torque: 98 N

⋅⋅⋅⋅m (10.0 kgf⋅⋅⋅⋅m/72 lb⋅ft)

3. Install lower ball joint and tighten the nut to the

specified torque, with just enough additional torque

to align cotter pin holes. Install new cotter pin.

Torque: 147 N

⋅⋅⋅⋅m (15.0 kgf⋅⋅⋅⋅m/108 lb⋅ft)

4. Install back plate.

5. Install wheel speed sensor.

6. Install stabilizer link nut. Right and left.