Isuzu KB P190. Manual — part 981

Automatic Transmission – 4L60E – On-vehicle Servicing

Page 7C4–11

3.2

Shift Selector Assembly

Figure 7C4 – 6

Legend

1 Rear

Console

2 Front

Console

3

Screw – Knob

4 Knob

5

Button – Knob

6

Spring – Knob

7 Selector

Lever

Assembly

8 Sleeve

9 Base

Plate

10

Upper Housing Assembly

11

Screw – Spring Plate

12 Spring

Plate

13 Grooved

Pin

14 Selector

Cable

15

Selector Lever Linkage

16 Lamp

17

Nut – Base Plate

Remove

1

Remove the front and rear console, refer to 10 Cab.

2

Position the transmission selector lever to the N position.

3

Remove the screw (3), two places, attaching the selector lever knob (4), refer to Figure 7C4 – 6.

Automatic Transmission – 4L60E – On-vehicle Servicing

Page 7C4–12

4

Remove the knob together with the button (5) and spring (6) from the selector lever assembly (7).

5

Turn the sleeve (8) counter clockwise to remove it, make note of the number of turns required to free it.

6

Remove the harness connectors from the base plate (9).

7

Remove the upper housing (10) which is held in place by four latched fasteners.

8

Remove the attaching screw (11) and spring plate (12).

9

Remove the grooved pin (13).

10

Using a small flat blade screwdriver, gently prise the upper end of the selector cable (14) from the pin on the
selector lever linkage (15).

11

Remove the selector lever assembly by pressing the rod down (lever in the N position).

12

If required, remove the lamp (16) from its socket by aligning the groove in the socket and the protruding part of the
lamp.

13

If required, remove the nut (17), four places, and the shift selector base plate.

Reinstall

1

Apply MULTEMP No 2 grease, or equivalent to the selector lever as indicated in Figure 7C4 – 7.

Figure 7C4 – 7

2

If required, install the shift selector base plate (9) and tighten the nut (17), four places, to the correct torque
specification, refer to Figure 7C4 – 6.

Shift selector base plate attaching nut
torque specification . . . . . . . . . . . ..7.0 Nm

3

Install the selector lever assembly (7) to the base plate:

a

insert and secure the rod,

b

insert the paw led end of the selector lever linkage (15) into the base plate hole,

c

attach the end of the selector cable to the pin on the selector lever linkage,

Automatic Transmission – 4L60E – On-vehicle Servicing

Page 7C4–13

d

Install the grooved pin (13) in the selector lever.

4

Insert the grooved pin in the base plate détente groove
until it touches the front wall. The selector lever is in
the N position.

Figure 7C4 – 8

5

Install the spring plate (12) and tighten the screw (11) to the correct torque specification, refer to Figure 7C4 – 6.

Spring plate attaching screw
torque specification . . . . . . . . . . . ..2.0 Nm

6

With the selector lever knob temporarily installed, ensure the grooved pin of the selector lever moves smoothly in
the base plate détente groove.

7

Temporarily install the sleeve (8).

8

If previously removed, install the lamp (16) by aligning the groove in the socket and the protruding part of the lamp
and rotate the lamp 90 degrees clockwise.

9

Attach the harness connectors to the base plate.

10

Position the transmission selector lever to the P position.

11

Install the sleeve (8) by rotating it clockwise the same number of turns as noted on removal.

12

Fit the upper housing (10) over the selector lever assembly, do not secure at this stage.

13

Install the knob (4) together with the button (5) and spring (6) to the selector lever assembly.

14

Adjust the clearance (2) between the base plate
détente groove and the grooved pin by moving the
selector lever knob sleeve (1).

Base plate détente groove and
grooved pin clearance. . . . . . . . 0.2 – 1.0 mm

Figure 7C4 – 9

15

Install the screw (3), two places, attaching the knob and tighten to the correct torque specification, refer to
Figure 7C4 – 6.

Automatic Transmission – 4L60E – On-vehicle Servicing

Page 7C4–14

Selector lever knob attaching screw
torque specification . . . . . . . . . . . ..2.0 Nm

16

Secure the upper housing (10) to the base plate with the four latched fasteners.

17

Install the front and rear console, refer to 10 Cab.

3.3

Selector Cable Assembly

Figure 7C4 – 10

Legend

1 Selector

Cable

2 Selector

Lever

Linkage

3

Retaining Pawl – Selector Cable

4

Shift Selector Base Plate

5

Screw – Heat Shield

6

Screw – Heat Shield

7 Heat

Shield

8

External Manual Shaft Linkage

9 Bracket

10 Bolt

–

Bracket