Isuzu KB P190. Manual — part 1133
UNIT REPAIR (JR405E) 7A4-55
01L&R-CS05
Legend
1. Seal ring
2. Low one-way clutch inner race
3. Return spring
4. Low and reverse brake piston
5. Seal ring
6. Lip seal
7. Transmission case
8. Snap ring
9. Retaining plate
10. Driven plate
11. Drive plate
12. Dish plate
04CASE-AY52
Disassembly steps
1. Harness assembly
Remove the fixing bolt and the harness assembly.
7A4-56 UNIT REPAIR (JR405E)
05CASE-AY30
2. Parking rod
• Use a pin punch to force out the parking rod spring pin.
06CASE-AY37
• Rotate the manual plate as you pull the parking rod free.
08CASE-AY45
3. Detent spring
Remove the fixing bolt and the detent spring.
09CASE-AY28
4. Manual shaft and manual plate
• Remove the manual shaft spring pin.
10CASE-AY21
• Remove the manual shaft together with the manual
plate.
UNIT REPAIR (JR405E) 7A4-57
11CASE-AY01
5. Oil seal
Using a screwdriver, remove the oil seal from the
transmission case.
Inspection
2 – 4 brake drive plates
Measure the 2-4 brake drive plate facing thickness at 3
points and calculate the average value.
If the average value is less than the specified limit, the 2-4
brake drive plate must be replaced.
2 – 4 brake drive plate facing thickness:
Standard = 2.0 mm (0.079 in)
Limit = 1.8 mm (0.071 in)
Low and reverse brake drive plates
Measure the low and reverse brake drive plate facing
thickness at 3 points and calculate the average value.
If the average value is less than the specified limit, the low
and reverse drive plate must be replaced.
Low and reverse brake drive plate facing thickness:
Standard = 2.0 mm (0.079 in)
Limit = 1.8 mm (0.071 in)
2 – 4 brake return springs
• Check the number of effective 2-4 brake return spring
coils.
Effective return spring coils (Standard): 10.2
• Measure the 2-4 brake return spring outside diameter,
free length, and linear diameter.
If any of the measured values exceed the specified limit,
the 2-4 brake return spring must be replaced.
2 – 4 brake return spring measurements (Standard):
Outside diameter = 6.9 mm (0.272 in)
Free length = 22.5 mm (0.886 in)
Linear diameter = 1.1 mm (0.043 in)
Low and reverse brake return springs
• Check the number of effective low and reverse brake
return spring coils.
Effective return spring coils (standard): 4.8
• Measure the low and reverse brake return spring outside
diameter, free length, and linear diameter.
If any of the measured values exceed the specified limit,
the low and reverse return spring must be replaced.
Low and reverse brake return spring measurements
(Standard):
Outside diameter = 11.2 mm (0.441 in)
7A4-58 UNIT REPAIR (JR405E)
Free length = 22.3 mm (0.878 in)
Linear diameter = 1.1 mm (0.043 in)
12CASE-AY06
Reassembly steps
1. Oil seal, manual shaft, and manual plate
• Use the oil seal installer to force the manual plate oil
seal into place.
Oil seal installer: 5-8840-2758-0
14CASE-AY21
• Install the manual shaft together with the manual plate.
15CASE-AY26
• Drive the spring pin into the transmission case.
16CASE-AY37
2. Parking rod
• Rotate the manual plate while installing the parking rod.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст