Isuzu KB P190. Manual — part 938

Exhaust System – V6

Page 6F – 4

Figure 6F– 3

Legend

1

Front Exhaust Pipe LH side

2

Front Exhaust Pipe RH side

3

Three Way Catalytic Converter

4

Centre Exhaust Pipe

5

Exhaust Silencer and Tail Pipe

1.2 General

Description

When inspecting or replacing the exhaust system components, make sure there is adequate clearance from all points
on the underbody to prevent overheating of the floor pan and possible damage to the passenger compartment insulation
and trim materials. Check complete exhaust system and nearby body areas and rear compartment lid for broken ,
damaged, missing or misaligned components, open seams, holes, loose connections or other deterioration which could
permit exhaust fumes to seep into the rear compartment or passenger compartment. Dust or water in the rear
compartment may be an indication of a problem in one of these areas. Any faulty areas should be corrected
immediately.

Various types of hangers are used to support exhaust systems, these include conventional rubber straps, rubber rings
or rubber blocks. The installation of exhaust system supports is very important, Improperly installed supports can cause
annoying vibrations which can be difficult to diagnose.

Exhaust System – V6

Page 6F – 5

Service Notes

1. Vehicles fitted with catalytic converters should not be operated with leaded petrol. Lead will contaminate

the ceramic monolith.

2. Do not drop the catalytic converter as it will damage the ceramic monolith.

3. Replace the catalytic converter if it is damaged.

4. Do not allow water, oil or fuel to enter the converter as the ceramic monolith will be contaminated.

5. Do not use engine and/or fuel additives unless approved by General Motors. Many additives contain

phosphorous that will contaminate the ceramic monolith.

6. The vehicle must not be started by pushing or towing, as unburned fuel could reach the catalytic

converter and destroy the ceramic monolith. Always use jumper leads to start a vehicle that has a flat or
defective battery.

7. When carrying out a compression test, for V6 engines use Tech 2 to ensure the output control Engine

Compression Test is set to enable, refer to 6A1 Engine Mechanical. This prevents fuel injection and
ignition during engine cranking.

8. Do not drive the vehicle with the engine misfiring or with any of the spark plug leads disconnected, as the

catalytic converter will overheat.

9. Do not coast downhill with the engine misfiring or with any of the spark plug leads disconnected.

10. The catalytic converter is serviceable as part of the front exhaust assembly only. Refer to the service

operations in this section for details of front exhaust pipe assembly removal and reinstallation.

11. The exhaust flange gaskets must be replaced whenever a new exhaust pipe, muffler or catalytic converter

is installed.

1.3

WARNING, CAUTION and NOTES

This Section contains various WARNINGS, CAUTIONS and NOTE statements that you must observe carefully to reduce
the risk of death or injury during service, repair procedures or vehicle operation. Incorrect service or repair procedures
may damage the vehicle or cause operational faults. WARNINGS, CAUTION and NOTE statements are not exhaustive.
HOLDEN LTD can not possibly warn of all the potentially hazardous consequences of failure to follow these instructions.

1.1 Definition of WARNING, CAUTION and NOTE Statements

Diagnosis and repair procedures in this Section contain both general and specific WARNING, CAUTION and NOTE
statements. HOLDEN LTD is dedicated to the presentation of service information that helps the technician to diagnose
and repair the systems necessary for proper operation of the vehicle. Certain procedures may present a hazard to the
technician if they are not followed in the recommended manner. WARNING, CAUTION and NOTE statements are
designed to help prevent these hazards from occurring, but not all hazards can be foreseen.

WARNING defined

A WARNING statement immediately precedes an operating procedure or maintenance practice which, if not correctly
followed, could result in death or injury. A WARNING statement alerts you to take necessary action or not to take a
prohibited action. If a WARNING statement is ignored, the following consequences may occur:

•

Death or injury to the technician or other personnel working on the vehicle,

•

Death or injury to other people in or near the workplace area, and / or

•

Death or injury to the driver / or passenger(s) of the vehicle or other people, if the vehicle has been improperly
repaired.

CAUTION defined

A CAUTION statement immediately precedes an operating procedure or maintenance practice which, if not correctly
followed, could result in damage to or destruction of equipment, or corruption of data. If a CAUTION statement is
ignored, the following consequences may occur:

•

Damage to the vehicle,

•

Unnecessary vehicle repairs or component replacement,

Exhaust System – V6

Page 6F – 6

•

Faulty operation or performance of any system or component being repaired,

•

Damage to any system or components which depend on the proper operation of the system or component being
repaired,

•

Faulty operation or performance of any systems or components which depend on the proper operation or
performance of the system or component under repair,

•

Damage to fasteners, basic tools or special tools and / or

•

Leakage of coolant, lubricant or other vital fluids.

NOTE defined

A NOTE statement immediately precedes or follows an operating procedure, maintenance practice or condition that
requires highlighting. A NOTE statement also emphasises necessary characteristics of a diagnostic or repair procedure.
A NOTE statement is designed to:

•

Clarify a procedure,

•

Present additional information for accomplishing a procedure,

•

Give insight into the reasons for performing a procedure in the recommended manner, and / or

•

Present information that gives the technician the benefit of past experience in accomplishing a procedure with
greater ease.

Exhaust System – V6

Page 6F – 7

2

Front and Centre Exhaust Pipe

Figure 6F– 4

1

Front Exhaust Flange Nuts

2

Front O2 Sensor

3

Three Way Catalytic Converter RH side

4

Rear O2 Sensor

5

Three Way Catalytic Converter LH side

6

Front Exhaust Pipe Mounting Rubber

7

Centre Exhaust Flange Attaching Nuts

8

Centre Exhaust Pipe

9

Rear Exhaust Flange Nuts

Removal

1. Disconnect the battery ground cable.

2. Remove the suspension cross member, Refer to 7B1 Manual transmission.

3. Remove the two front torsion bar springs, Refer to 3C Suspension.

4. Disconnect the O2 sensor harness connectors (2 and 4), two each bank.

5. Remove the front exhaust flange attaching nuts (1), three each bank.

6. Remove the centre exhaust pipe flange nuts (7), two each bank.

7. Remove the centre exhaust pipes from the rubber mounts (6).

8. Remove the front left and right hand exhaust pipes from the vehicle.

9. Remove the two rear exhaust flange nuts and bolts (9).

10. Remove the centre exhaust pipe from the vehicle.

11. Remove the O2 sensors if required, Refer to 6C1 – 1 Engine Management General Info.