Nissan Almera Tino V10. Manual — part 179
AT-440
[ALL]
REPAIR FOR COMPONENT PARTS
4.
Remove O-ring from oil pump housing.
5.
Remove oil pump housing oil seal.
INSPECTION
Oil Pump Housing, Oil Pump Cover, Inner Gear and Outer Gear
●
Check for wear or damage.
Side Clearances
●
Measure side clearance of inner and outer gears in at least four
places around each outside edge. Maximum measured values
should be within specified positions.
●
If clearance is less than standard, select inner and outer gear as
a set so that clearance is within specifications.
●
If clearance is more than standard, replace whole oil pump
assembly except oil pump cover.
SAT093D
SAT094D
Standard clearance: 0.02 - 0.04 mm (0.0008 - 0.0016 in)
Inner and outer gear:
Refer to
AT-519, "SERVICE DATA AND SPECIFICA-
SAT095D
REPAIR FOR COMPONENT PARTS
AT-441
[ALL]
D
E
F
G
H
I
J
K
L
M
A
B
AT
●
Measure clearance between outer gear and oil pump housing.
●
If not within allowable limit, replace whole oil pump assembly
except oil pump cover.
Seal Ring Clearance
●
Install new seal rings onto oil pump cover.
●
Measure clearance between seal ring and ring groove.
●
If not within allowable limit, replace oil pump cover assembly.
ASSEMBLY
1.
Install oil seal on oil pump housing.
●
Apply ATF to oil seal.
2.
Install O-ring on oil pump housing.
●
Apply ATF to O-ring.
Standard clearance: 0.08 - 0.15 mm (0.0031 - 0.0059 in)
Allowable limit: 0.15 mm (0.0059 in)
SAT096D
Standard clearance: 0.1 - 0.25 mm (0.0039 - 0.0098 in)
Allowable limit: 0.25 mm (0.0098 in)
SAT097D
SAT922D
SAT093D
AT-442
[ALL]
REPAIR FOR COMPONENT PARTS
3.
Install inner and outer gears on oil pump housing.
●
Take care with the direction of inner gear.
4.
Install oil pump cover on oil pump housing.
a.
Wrap masking tape around splines of oil pump cover assembly
to protect seal. Position oil pump cover assembly on oil pump
housing assembly, then remove masking tape.
b.
Tighten bolts in a crisscross pattern. Tighten oil pump cover
bolts to the specified torque. Refer to
.
5.
Install new seal rings carefully after packing ring groove with
petroleum jelly.
●
Do not spread gap of seal ring excessively while install-
ing. The ring may be deformed.
SAT092D
SAT101D
SAT699H
REPAIR FOR COMPONENT PARTS
AT-443
[ALL]
D
E
F
G
H
I
J
K
L
M
A
B
AT
Control Valve Assembly
ECS009CJ
COMPONENTS
1.
Solenoid valve assembly
2.
O-ring
3.
Clip
4.
Terminal body
5.
Control valve lower body
6.
Oil strainer
7.
Support plate
8.
Lower inter separating gasket
9.
Separating plate
10. Lower separating gasket
11.
Steel ball
12. Control valve inter body
13. Pilot filter
14. Upper inter separating gasket
15. Separating plate
16. Upper separating gasket
17
Steel ball
18. Control valve upper body
19. Check ball
20. Fluid cooler relief valve spring
21. O-ring
22. T/C pressure holding spring
23. Check ball
SAT868J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст