Nissan Rogue. Manual — part 406
DLN-68
< REMOVAL AND INSTALLATION >
[TRANSFER: TY21C]
AWD CONTROL UNIT
REMOVAL AND INSTALLATION
AWD CONTROL UNIT
Exploded View
INFOID:0000000011278358
Removal and Installation
INFOID:0000000011278359
REMOVAL
1. Remove luggage side lower finisher (LH). Refer to
.
2. Disconnect harness connector from the AWD control unit.
3. Remove AWD control unit bolts (A).
NOTE:
AWD control unit (1) is located on the back side of body panel.
4. Remove AWD control unit.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not drop or shock AWD control unit.
• When replacing AWD control unit, perform writing unit characteristic. Refer to
.
1.
AWD control unit
Front
JSDIA5368GB
: Front
AWDIA1232ZZ
AWD LOCK SWITCH
DLN-69
< REMOVAL AND INSTALLATION >
[TRANSFER: TY21C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
AWD LOCK SWITCH
Exploded View
INFOID:0000000011278360
Removal and Installation
INFOID:0000000011278361
REMOVAL
1. Remove instrument lower panel LH. Refer to
IP-23, "Removal and Installation"
2. Disconnect AWD lock switch harness connector (A).
3. Release pawls using suitable tool and remove AWD lock switch
from lower switch bracket (1).
INSTALLATION
Install in the reverse order of removal.
1.
Instrument lower panel LH
2.
AWD lock switch
Front
Pawl
ALDIA0506ZZ
: Pawls
ALJIA1522ZZ
DLN-70
< REMOVAL AND INSTALLATION >
[TRANSFER: TY21C]
TRANSFER COVER OIL SEAL
TRANSFER COVER OIL SEAL
Removal and Installation
INFOID:0000000011278362
NOTE:
• Replacement on vehicle may cause damage to transfer cover, and may cause a transfer oil leak.
• If transfer cover oil seal requires replacement, remove the transfer assembly from the vehicle before replac-
ing transfer cover oil seal. Refer to
.
TRANSFER ASSEMBLY
DLN-71
< UNIT REMOVAL AND INSTALLATION >
[TRANSFER: TY21C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
UNIT REMOVAL AND INSTALLATION
TRANSFER ASSEMBLY
Exploded View
INFOID:0000000011278363
Removal and Installation
INFOID:0000000011278364
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove front drive shaft (RH). Refer to
FAX-23, "Removal and Installation (RH)"
2. Remove front suspension member. Refer to
FSU-22, "Removal and Installation"
3. Remove front exhaust tube. Refer to
4. Remove rear propeller shaft. Refer to
DLN-100, "Removal and Installation"
5. Remove transaxle assembly to transfer assembly bolts.
CAUTION:
Be careful not to damage gear ring oil seal inside of CVT.
6. Remove transfer assembly from the vehicle.
CAUTION:
• Do not damage air breather hose.
• After removing transfer from transaxle, always replace
differential side oil seal of the transaxle side with new
one. Refer to
TM-210, "Removal and Installation"
.
INSTALLATION
Installation is in the reverse order of removal.
Transfer assembly
: N·m (kg-m, ft-lb)
*: Apply anti-corrosion oil.
JSDIA5370GB
Bolt No.
(A)
(B)
Quantity
4
2
Bolt length “ ” mm (in)
44 (1.73)
42 (1.65)
ALDIA0389ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст